CAUTION!
THE LIGHT SOURCE OF THIS LUMINAIRE IS NOT REPLACEABLE;
WHEN THE LIGHT SOURCE REACHES ITS END OF LIFE THE WHOLE LUMINAIRE SHALL BE
REPLACED.
CAUTION: Any change or modification to product not expressly recognized by OttLite
Technologies voids OttLite’s responsibility for proper function of product.
POWER ADAPTER SPECIFICATION:
Input: 100-240 V~, 50/60 Hz, 0.9 A
Output: 12V 2.5A with a Male DC Plug
Qi CHARGER SPECIFICATION:
Output: 5V 1A
THIS LAMP CONTAINS a 5V, 2.1A USB output port (Q) located on the bottom rear of
lamp. USB port can charge items such as tablets, cellular phones, etc.
The “Qi” symbol is a trademark of the Wireless Power Consortium. All phones with
integrated wireless charging support “Qi”.
This symbol on the product or on its packaging indicates
that this product (including batteries) shall not be treated
as household waste. Instead it shall be handed over to the
applicable collection point for the recycling of electrical
and electronic equipment. By ensuring this product is
disposed of correctly, you will help prevent potential negative
consequences for the environment and human health,
which could otherwise be caused by inappropriate waste.
Disposal of Old Electrical & Electronic Equipment
For more detailed information about recycling of this product, please
contact your local Council, your household waste disposal service or the
shop or source where you purchased the product.
DECLARATION OF CONFORMITY
PRODUCT: B22FS Wireless Charging LED Lamp with Colour Changing Base
MANUFACTURER: OttLite Technologies, Inc.
1715 N. Westshore Blvd. Suite 950, Tampa, FL 33607. USA
Declares CE marking in accordance with the following EU directives
and normative standards.
Hereby, OttLite Technologies Inc. declares that the equipment type B22FS is in
compliance with Directive 2014/53/EU.
working range: 110-205KHz
Transmitting frequency: -22.4 dBuA/m at 10m distance
WARNING: FIRE AND ELECTRIC SHOCK
HAZARD
• Do not expose the charger to liquid, moisture, humidity, or rain. Do not use the
charger near a bathtub, sink, sauna, pool, or steam room. Exposing of the charger to
moisture could result in electric shock.
• Do not drop, dissassemble, open, crush, bend, deform, puncture, shred, microwave,
incinerate, paint, or insert foreign objects into the charger. Such actions could result
in electric shock.
• Clean the charger only with a dry cloth
• Do not expose the charger to extremely high or low temperatures
• Do not expose the charger to sources of excessive heat, such as sunlight, fire, etc.
Do not place the charger near open fire sources, such as gas burners, candles, or
fireplaces, and avoid contact with direct solar radiation. Do not place any candles or
other open-flame sources on the device. Make sure that the charger has sufficient
ventilation.
ACCESSORIES AND SOFTWARE INFORMATION:
It is recommended that the following accessories should be used:
The product software version is 2250-V1.0. Software updates will be released by the
manufacturer to fix bugs or enhance functions after the product has been released.
All software versions released by the manufacturer have been verified and are still
compliant with the related rules.
All RF parameters (for example, frequency range and output power are not accessible to
the user, and cannot be changed by the user.
After evaluation, the product satisfied with RED Directive RF exposure required
while used 20cm away from the human body.
EU REGULATORY CONFORMANCE
Frequency bands and power (a) Frequency bands 110-205KHz. (b) Maximum radio-
frequency power transmitted in the frequency bands in which the radio equipment
operates: The maximum power for all bands is less than the highest limit value specified
in the related Harmonized Standard. The frequency bands and transmitting power
(radiated and/or conducted) nominal limts applicable to this radio equipment are as
follows: 6dBuA/m at 10m distance.
STANDARDS:DIRECTIVES:
Tampa, May 2021 | K. Albinus | Quality Assurance
EN 60958-1:2015
+A1:2021
Luminaires –
Part 1: General requirements and tests
EN 60598-2-4:2018 General Purpose Luminaire;
Portable Requirements
EMC Directive
2014/30/EU
RED Directive
2014/53/EU
EN 60950-1:2006
EN 61347-2-11:2008
EN 61347-1:2015
Information technology equipment. Saftey.
General requirements.
Lamp Control Gear - Part 2-11: Particular
requirements for miscellaneous electronic
circuits used with luminaires
General and safety requirements for lamp
controlgear for use on D.C. supplies
EN 55015:2020
EN 61547:2009
EN 61000-3-2:2021
EN 61000-3-3:2019
EN 62311:2008
EMC for Luminaires
EMC Immunity
Current Harmonics
Voltage Fluctuations
Exposure Restrictions for EMF (0Hz - 300 GHz)
Low Voltage Directive
2014/35/EU
EN 62031:2008
+A1:2013+A2:2015
LED modules for general lighting safety
specifications
EN 62493:2015 Assessment of lighting equipment related to
human exposure to electromagnetic fields
EN 62311: 2020
EN 60598-1: 2015 + A1:2018
EN 60598-2-4: 2018
EN 62368-1:2014+A11:2017
Saftey and Health
(Article 3.1a)
EMC
(Article 3.1b)
EN IEC 55015:2019/A11:2020
EN 61547: 2009
EN 61000-3-2: 2014
EN 61000-3-3: 2013
ETSI EN 301 489-1 V2.2.3 (2019-11)
ETSI EN 301 489-3 V2.1.1 (2019-03)
Radio
(Article 3.2)
ETSI EN 303 417 V1.1.1 (2017-09)
EN 61347-2-11: 2001
General and safety requirements for miscellaneous
electronic circuits used with luminaires
To Previous Page
Loading...
