OUMAN EH-80 - User Manual

Blinking On continuously
The controller is The valve is competely open.
increasing the heat. Not enough heat in the boiler.
(Valve is opening)
The controller is The valve is closed. In the
decreasing the heat summer when no heat is
(Valve is closing) needed this lamp may always
be on.
The unit is operating.
For example, read control curve C as follows:
CONTROL CURVES
* If the room temperature is always too cool, turn knob
B in the + direction.
* If the room temperature is always too warm, turn
knob B in the - direction.
One step of the scale of knob B changes the outgoing
water temperature by 4°C, corresponding to about 1°C
in the room temperature.
Select a house-specific control curve
with knob A.
Set the basic setting according to the
table below.
BOILER OR
ACCU-
MULATOR
HEATING
NETWORK
BOILER OR
ACCU-
MULATOR
HEATING
NETWORK
Heating characteristics of the building Position of knob A
Well-insulated house (radiator heating) C...D
House with poor heating characteristics E... F
House with a floor heating system A...B
C
B
D
E
A
F
Curve C is selected in this example. If the room
temperature goes down when the weather gets cold,
select a steeper curve. If the room temperature goes up,
select a lower curve. A suitable curve for your house may
be between the plotted curves.
If the room temperature is even, but
it is too cool or warm, make a fine
adjustment with knob B.
+
NOTE ! Changes in the settings are felt quite slowly.
Wait a few hours before making additional adjustments.
–
Knob B raises and
lowers the selected
curve.
Select the steepness of
the curve with knob A
C
B
D
E
AF
The OUMAN controller contains a wide range of
control curves that are designed to respond to very
different kinds of heating conditions. It also has low
curves suitable for houses with floor heating.
C
80
100
60
40
20
Outgoing water temperature
Outdoor temperature
20100-10-20-30
°C
When it is -20°C, the outgoing water is 50°C
When it is 10°C, the outgoing water is 44°C
When it is 0°C, the outgoing water is 37°C
INDICATOR LAMPS
MANUAL OPERATION
+–
A
+
–
ON
LED
If the green ON indicator lamp is not on, check that
the transformer is plugged in and the transformer lead
is connected. Check the line voltage.
B
MIN - MAX - LIMITS
The settings located behind the
instruction booklet under the clear
cover are usually set only when the
controller is taken into use the first time.
The minimum limit knob sets the lowest
allowable outgoing water temperature
(if sufficient heat is available).
The maximum limit knob sets the
highest allowable outgoing water
temperature. This is especially beneficial
in floor heating systems, where overly
hot water may cause damages.
OUMAN
OUMAN
OUMAN
OUMAN
OUMAN OUMAN
OUMAN OUMAN
OUMAN automatically adjusts the
temperature of the water entering the
network. The heat requirement varies
according to the outdoor
When the weather gets cooler, OUMAN
releases just enough heat into the network
to maintain an even room
temperature.
OPERATING PRINCIPLE
The OUMAN 80 can also be used manually. Unplug the
transformer to disconnect the operating voltage. Press
the button on the bottom right all the way down while
turning the valve to the desired position with the manual
control lever.
NOTE ! If you wish to disconnect the controller for a
longer period (e.g., in summer), disconnect the operating
voltage (13 VAC) connector from the controller. The
clock battery will also be disconnected to avoid unnecessary
battery drainage (battery life = about 180 days). The
battery is a backup power supply for the clock and
programming during power shortages.
FINE ADJUSTMENT
BASIC SETTING
EH-80
BASIC SETTING, KNOB A
If the room temperature goes down when the
weather gets colder, select a steeper curve
and vice versa.
C
B
D
E
A
F
80
100
60
40
20
Outdoor temperature
20
10
0-10
-20
-30
°C
OPERATING INSTRUCTIONS
EH-80
EH-80
FINE ADJUSTMENT, KNOB B
If the room temperature is always too cool or
warm, turn knob B in the desired direction;
+ raises, - lowers the temperature.
Outgoing water temperature
EH-80
EH-80 EH-80
EH-80 EH-80

Summary

OUMAN EH-80 Operating Principles and Settings

Operating Principle

Explains how the OUMAN controller automatically adjusts water temperature based on outdoor conditions.

Control Curves

Details the range of control curves available for different heating conditions, including floor heating.

Indicator Lamps

Describes the function and meaning of the LED indicator lamps on the controller.

Basic Setting

Guides on selecting a house-specific control curve using Knob A based on building characteristics.

Fine Adjustment

Explains how to fine-tune room temperature using Knob B for desired heating comfort.

Manual Operation

Instructions for operating the OUMAN EH-80 manually by bypassing timer programs.

OUMAN EH-80 Optional Equipment and Functions

Room Compensation TMR;P

Details the optional room compensation unit for improved temperature control in specific conditions.

Timer Functions

Covers timer installation, setting temperature drops, vacation function, and programmed periods.

Setting Time and Programs

Guides for setting the clock, drop times, vacation periods, and browsing/adding programs.

Forced Control and Program Clearing

Explains temporary forced control and how to clear all programmed settings.

OUMAN EH-80 Specifications

General

Brand	OUMAN
Model	EH-80
Category	Temperature Controller
Language	English