To Next PageTo Next Page
Need help?Do you have a question about the Outdoor living today 9x6 Cabana and is the answer not in the manual?
General| Size | 9x6 |
|---|---|
| Category | Garden Houses |
| Color | Natural |
| Assembly Required | Yes |
| Material | Cedar |
| Roof Type | Cedar Shingles |
List of all components for the floor section of the cabana.
List of all components for the wall section of the cabana.
List of all components for the rafter and roof section of the cabana.
List of all components for the miscellaneous finishing section.
List of all hardware components included in the assembly kit.
List of tools necessary for building the cabana.
Connect interior floor joists to the floor joist frames using screws.
Attach interior joists to the outside floor joist frames with screws.
Assemble completed floor joist frames together using screws.
Secure floor runners to the completed floor frame using screws.
Carefully flip the assembled floor onto its foundation, ensuring it is level.
Place plywood floor pieces on joists and secure with screws.
Ensure the completed floor is level and make adjustments as needed.
Arrange wall panels to identify their correct positions before assembly.
Secure wall plates to the bottom of wall studs on each panel.
Place the first solid wall panel at the rear corner of the floor.
Align front and rear wall panels flush with the floor end, sandwiching side panels.
Place and attach the first side wall panel to the floor and rear wall.
Position and secure the second rear wall panel to the structure.
Position and secure the third rear wall panel as per previous step.
Complete the attachment of the remaining side walls following prior steps.
Insert window panels into wall openings and secure them with screws.
Position and attach the window wall panels to the structure.
Secure vertical door jambs to the door opening wall studs.
Fasten the door header to the vertical door jambs.
Check wall alignment and fasten bottom wall plates to the floor.
Position and attach side top plates to the top of the wall framing.
Secure front and rear top plates to the wall frame, fitting between side top plates.
Position and attach side gable walls to the top plate, ensuring proper alignment.
Align and attach the second side gable wall according to previous instructions.
Connect ridge boards using connectors and screws to form two sets.
Lay out rafters and soffits, doubling up rafters as illustrated.
Secure ridge boards to the ends of the outside and interior rafters.
Attach soffit boards to the ends of the rafters, ensuring flush alignment.
Flip the assembled rafter section and lift it onto the gable framing.
Slide the rafter section up until the ridge board fits into the gable notch.
Ensure rafters are evenly spaced and soffits sit flush against the walls.
Position and attach the second completed rafter section to the gable walls.
Align and secure ridge boards at the peak, ensuring they are flush.
Attach gable framing to the outside rafters with screws for stability.
Place roof gussets on middle rafters and secure after aligning walls.
Complete the attachment of the remaining roof gussets following the same procedure.
Secure Simpson Strong Ties to the top wall framing and underside of rafters.
Identify outside and middle roof panels and place an outside panel on rafters.
Position and secure the first outside roof panel to the rafters.
Place and secure the middle roof panel to the rafters.
Position and attach the second outside roof panel to the rafters.
Position and secure the front roof panels following previous panel installation steps.
Secure roof panels to rafters and battens from the inside using screws and ties.
Prepare roof filler shingles for covering roof seams, starting at the bottom.
Secure the first filler shingle to the rafters using screws.
Slide and attach subsequent filler shingles, using pre-cut shingle for the last row.
Secure bottom skirting around the base of the shed to hide floor framing.
Align and attach filler trims to each corner side wall, flush with bottom skirting.
Attach wide and narrow corner trims in each corner, aligning narrow trim behind wide trim.
Position trims flush with bottom skirting and soffit, then attach with finishing nails.
Secure narrow trims to wall seams, flush with bottom skirting.
Position and attach horizontal gable trim to both sides of the shed over seams.
Secure side facia to roof panel battens, aligning flush with rafter ends.
Fasten front facia to roof rafter ends, ensuring it overhangs the side facia.
Position and secure ridge caps on the roof peak, overlapping roofing felt at the center.
Secure pentagon facia plates where side facia meet at the peak.
Position and attach doorway narrow trims flush with the door jamb and bottom skirting.
Attach hinges to the top and bottom dutch door sections, allowing for swing direction choice.
Position the bottom dutch door panel and attach it to the doorway seam trim with screws.
Place the top dutch door panel, ensuring a 1/4" gap at top and bottom, and attach hinges.
Secure horizontal door trim to cover the header using finishing nails.
Install door handle, exterior barrel bolt, and interior barrel bolt on the door.
Secure interior door stops to the door framing (jambs and header).
Mount window boxes below the window trim, securing them from the inside.
Locate and orient the door jamb on the side wall panel stud for the alternate configuration.
Secure the door jamb to the wall stud with screws for the alternate door position.
Attach vertical and horizontal door stops for the alternate door configuration.
