What to do if my Packard Bell DOTMA-111G16i has no POST or video?
If your Packard Bell Netbook is not displaying anything, ensure the internal display is selected. Try draining stored power by disconnecting the power cable and battery, then hold the power button for 10 seconds. Reconnect the power and reboot. Also, connect an external monitor and reseat the memory modules.
How to fix abnormal video display on Packard Bell Netbook?
To resolve abnormal video display issues on your Packard Bell Netbook, start by rebooting the computer. If the LCD is faulty, it should be replaced. Adjust the brightness to the highest level and verify that the display resolution is correctly configured. If you recently updated the video driver, roll it back to the previous version or try removing and reinstalling the video driver.
What to do if my Packard Bell DOTMA-111G16i Netbook HDD is not operating correctly?
If the HDD in your Packard Bell Netbook isn't working correctly, try these steps: Disconnect all external devices. Run a complete virus scan using up-to-date software. Additionally, run the Windows Vista Startup Repair Utility and Windows Check Disk by entering chkdsk /r from a command prompt.
What to do if my Packard Bell Netbook has no display issue?
If your Packard Bell Netbook has no display, replace the LCD Panel and ensure there is no LCD Module issue. Reconnect or replace the external DDRAM module. Also, remove and replace the thermal module.
What to do if my Packard Bell DOTMA-111G16i Netbook touchpad fails?
If the touchpad on your Packard Bell Netbook is not working, try re-assembling the T/P FFC to the mainboard. If that doesn't resolve the issue, swap or reassemble the T/P board. If problems continue, consider swapping the mainboard.
Why does my Packard Bell DOTMA-111G16i randomly lose BIOS settings?
If your Packard Bell Netbook is losing BIOS settings, and the computer is more than one year old, replace the CMOS battery. Run a complete virus scan with up-to-date software. Ensure all power and data cables between devices are securely reconnected. If the drive is defective, replace the HDD. As a last resort, consider replacing the Motherboard.
What to do if my Packard Bell DOTMA-111G16i Netbook has a built-in keyboard failure?
If the built-in keyboard on your Packard Bell Netbook isn't working, try disconnecting and reconnecting it. If that doesn't work, replace the keyboard. If the issue persists, consider replacing the mainboard.
How to troubleshoot LCD failure in Packard Bell Netbook?
To troubleshoot an LCD failure on your Packard Bell Netbook, check the LCD module and the MB LCD connector and cable. If these checks do not resolve the issue, consider swapping the mainboard.
How to resolve internal speaker failure on Packard Bell DOTMA-111G16i?
If the internal speakers on your Packard Bell Netbook aren't working, try re-assembling the speaker cable to the mainboard. If that doesn't work, swap the Logic upper/Logic lower components. As a last resort, consider swapping the mainboard.
What to do if Packard Bell Netbook USB fails?
If the USB ports on your Packard Bell Netbook are failing, check the USB/B to M/B cable. You can also try swapping the USB/B and check the USB/B. If the problem persists, consider swapping the mainboard.
General| RAM | 1GB DDR2 |
|---|---|
| Storage | 160GB HDD |
| Resolution | 1024 x 600 |
| Graphics | Intel GMA 3150 |
| Operating System | Windows 7 Starter |
| Wireless | 802.11b/g/n |
| Webcam | Yes |
| Battery Life | Up to 4 hours |
| Weight | 1.1 kg |
| Dimensions | 258.5 x 185 x 25.4 mm |
| Processor | Intel Atom N450 |
| Display | 10.1 inch |
| Battery | 3-cell |
To Next Page