How to Enjoy Music
Power on
PTY (Programme Type)/
MONO/LOC(Local)
AF (Alternative Frequency)/
REG (Region)
DISP (Display)/CT (Clock Time)
SRC (Source)/
POWER
MUTE/SQ (Sound Quality)
CD Slot Eject
]TUNE[
6 TRACK 7
Fast Forward/Fast Reverse
TA (Traffic Announcement)
VOLUME/SEL (Select)
● Press to power on.
● Press again and hold to power off.
1 to 6 (Preset Memory)
BAND/APM (Auto Preset Memory)/
y/
5
(Pause)
Turn to change each level
Turn to adjust
■ Sound Control ■ Sound Quality (SQ)
SQ is a function that can call up various sound types at the
touch of button in accordance with your listening music type.
Press and hold [MUTE] (SQ) for more than 2 seconds to select
the sound type as follows:
(default) :
flat frequency response:
does not emphasize.
(ROCK) :
speedy and heavy sound:
exaggerates bass and treble.
(POP) :
wide-ranged and deep sound:
slightly emphasizes bass and
treble.
(VOCAL) :
clear sound:
emphasizes middle tone and
slightly emphasizes treble.
Notes:
● If no operation takes place for more than 5 seconds in the SQ mode, the
display returns to the regular mode.
● Settings of SQ, bass/treble are influenced one another. If the influence
mentioned above causes distortion to audio signal, readjust bass/treble
or volume.
■ Volume Adjustment (Setting range: 0 to 40)
■ Mute
Sound Controls
(–12 to +12 in 2 dB step)
(–12 to +12 in 2 dB step)
(left/right: 1 to 15)
(front/rear: 1 to 15)
(0 to 40)
Bass
Treble
Balance
Note: If no operation takes place for 5 seconds or more (2 seconds in the volume
mode), the display return to the regular mode.
Fader
Press to select a mode
Press to switch on and off.
● Mute the sound completely.
Volume
Enjoy music in each mode
Radio
CD Player
When a disc is loaded.
Press to select a mode as follows.
MONO OFF/LOCAL OFF
MONO ON/LOCAL OFF
MONO ON/LOCAL ON
MONO OFF/LOCAL ON
Press to select a band.
FM1
FM2
FM3
AM (LW/MW)
Mono/Local Selection
Mono: Reduce noise if weak signals are received
Local: Only strong signals of stations are searched for in seek tuning.
Display Change
Program Service Name
Frequency
Clock Time
(3 seconds)
Note: A station name appears when it is an RDS station.
■ FM broadcast
Hold down [PTY] (MONO/LOCAL) for 2 seconds or more to
change the mode.
■ AM(LW/MW) broadcast
Press [PTY] (MONO/LOCAL) to change the mode.
1
PTY (MONO/LOC)
DISP
2
1
2
■ Seek tuning
Hold down for 0.5 seconds or more.
Tuning will automatically stop when the next sta-
tion is found.
[[]: higher frequency
[
]]: lower frequency
■ Manual Tuning
[[]: higher frequency
[
]]: lower frequency
LOCAL OFF
LOCAL ON
Press
Display Change
Press
FM broadcast AM(LW/MW) broadcast
Preset Memory
● Up to 6 stations can be stored in each of the FM1, FM2, FM3 and
AM (LW/MW) band selections.
Press to select a band for
preparation.
■ Auto Preset Memory
Hold down for 2 seconds or more.
● Automatically tune the 6 stations with good reception and
save under preset buttons [1] to [6].
● Preset stations appear for 5 seconds each.
Notes:
● Only RDS stations will be saved at default setting (AF is
ON).
● To stop scanning, press one of the preset buttons [1] to
[6].
■ Manual Preset Memory
Hold down one of the preset buttons [1] to [6] until
the display blinks once.
Note: New stations overwrite existing saved stations after following
this procedure.
Press
[1] to [6] to call a preset station.
Caution: Never preset stations while driving.
■ Preset station calling
Use seek or manual tuning to find a station.
Band
Preset Number
Frequency
Convenient
Function
Radio Data
System (RDS)
RDS is a system performing convenient functions for
FM stations in such as Europe. However, there may be
some areas where RDS is not effective for reception.
●Station name appears instead of the frequency.
●The clock is automatically adjusted.
AF
Alternative frequency
●When reception is poor, an RDS station broadcasting
the same program is tuned in automatically.
AF indicator
■ To select AF receiving sensitivity
a Press [AF]
AF1 : For mountain areas and places enclosed by high-
rise buildings or other objects that prevent radio
reception. (Default)
AF2 : For suburbs and other places free of obstructions
of view.
OFF : For the AF function inactivated.
■ To change AF range
a Hold down [AF] for 2 seconds or more.
●REGION ON : To select a station broadcasting the
same program
●REGION OFF : To select an AF station of the same net-
work
(The program may be different) (Default)
■ AF1 or AF2 auto preset memory
●The memory is valid for the RDS stations only.
●A station of the same network in good receiving condi-
tion is received.
●If a preset station is in poor receiving condition, anoth-
er station in good receiving condition can be tuned in
to by pressing the same preset button. (Best Station
Research)
●Another station broadcasting the same program is
searched for if a station with an appropriate frequency
cannot be found even by means of BSR (Best Stations
Research). (PI seek: Program Identification Seek)
Note: For PI Seek, cancel the TA mode first, then exe-
cute PI Seek.
TA
Traffic Announcements
●To automatically listen to a station
that gives traffic information periodically.
TA indicator TP indicator
Lights up while receiving a TP
station
■ To select TA mode
a Press [TA].
(Default : TA OFF)
8
To cancel a Press [TA] again.
Notes:
●
If a selected station is in poor receiving condition,
another station giving traffic announcements will be
automatically tuned in.
●When TA ON is selected, only TP station will be
searched. When TA ON is selected, only TP station will
be memorized automatically.
●Even in CD player mode, a station giving the traffic
information is automatically received.
■ To listen to TA only
a Hold down [TA] for 2 seconds or more (in FM
mode).
●To cancel
a Press [TA] again. (Or, raise the volume with
[VOL]).
■ TA Volume Set (Volume Level: 1 to 40)
a Turn [VOL] while receiving traffic announce-
ments.
●The TA volume differs from the regular volume (by up
to 5 levels).
Down Up
EON
Enhanced Other Networks
●Traffic information of the other networks is received.
●Preset AF data is refreshed at all times.
PTY
Program Type
●Stations can be selected by program type, for example,
news and rock.
PTY indicator
■ To select mode PTY
a Press [PTY].
●To cancel
aPress [PTY] again.
■ PTY preset call
a Press [1] to [6].
●The following program types are preseted.
■ PTY selection
q Press []TUNE[] to select a program type
below.
w Press [BAND] for automatic selection.
■ PTY preset change
q Select a program type by using PTY selection
or PTY preset call.
w Hold down [1] to [6] for 2 seconds or more.
Note: When there is no corresponding program type,
“NO PTY” is displayed.
■ Emergency Announcement
●An emergency announcement, if broadcast, is automat-
ically received.
●This function operates in other than the radio mode,
and “ALARM” flashes.
Note: Press [DISP] to switch the PTY display language
to Swedish.
To Previous Page
Loading...
