Before use
WARNING: Keep the trimmer dry.
This Beard/Hair Trimmer is for the
trimming and care of mustaches and
beards.
Trimming length can be adjusted
between 2 to 18 mm.
The Trimmer can be operated either
from an AC power source or on its
rechargeable battery.
When charging the Trimmer for the first
time or when it has not been in use for
more than 6 months, charge it for at
least 16 hours before use (ER2051
needs 8 hours).
Parts Identification (See Fig. 1)
(A) Switch
Slide up to turn on, Slide down to
turn off.
(B) Charge Indicator Lamp
Lights when the unit is connected
with the cord (K) to an AC power
source for charging.
(The lamp flashes when recharging
is completed. [ER2051])
(C) Main Blade
A precision 39 mm‑wide blade
which can be used with the comb
attachment (F).
(D) Dial
First push, then turn the dial to a
higher setting to raise the comb
attachment (F) to the desired
length (between 2 and 18 mm).
Even if the attachment is released,
the trimming length you set is
retained.
(E) Blade Release Button
Slide up to release the main blade.
(F) Comb Attachment
Use this to control trimming length.
(See Fig. 2)
(G) Stationary Blade
(H) Movable Blade
(I) Cleaning Lever
Push on this lever to remove bits of
hair caught between the stationary
blade (G) and the movable blade
(H).
(J) Blade Block
Release them to remove blade
block from the housing to clean or
replace the blade.
(See Fig. 3, 4, 5)
(K) Power Cord
Use this to plug the Trimmer into an
AC power source for recharging or
for AC operation.
(L) Oil
Lubricate the spaces between the
stationary (G) and movable blade
(H) with a few drops of oil after use.
(See Fig. 6)
(M) Cleaning Brush
Trimming Length Indicator
Indicator Beard Length
1 2.0 mm
• 3.0 mm
2 4.5 mm
• 6.0 mm
3 7.5 mm
• 9.0 mm
4 10.5 mm
• 12.0 mm
5 13.5 mm
• 15.0 mm
6 16.5 mm
• 18.0 mm
Operation
Using the rechargeable battery
Charge the battery by plugging the
Trimmer into an AC source using the
cord (K).
The switch (A) should be set to
“0‑charge” during charging.
The Trimmer can be used for about 40
minutes after an 8‑hour charge.
[ER2031]
The Trimmer can be used for about 40
minutes after a 1‑hour charge.
[ER2051]
Using an AC power source
Plug the Trimmer into an AC power
source using the cord (K) with the
switch (A) set to “0‑charge.” Wait about
10 seconds, then turn the switch (A)
on.
After use, return the switch to the
“0‑charge” position.
Maintenance
Care of the blades
• Hold the body of the Trimmer, slide up
the main blade release button (E),
squeeze both edges of the blade
block to remove. (See Fig. 3)
• Brush the blade block clean and push
on the cleaning lever (I) to remove
bits of hair caught between the
blades.
(See Fig. 5)
• Lubricate the places indicated in
Fig. 6 with a few drops of oil.
• Reassemble as shown in Fig. 4. First
place the blade block to the correct
position (1), then push until it snaps in
place. (2) (3) (See Fig. 4)
Blade Life
Blade life will vary according to the
frequency and length of use.
For example, using the unit for 10
minutes every 3 days, the life
expectancy is approximately 3 years.
If cutting efficiency is reduced
substantially despite proper
maintenance, the blades have
exceeded their service life and should
be changed.
Battery life
Battery life will vary according to the
frequency and length of use.
If the battery is charged 3 times a
month, the service life will be
approximately 6 years.
If the unit is left without being charged
for more than 6 months, the charge will
drain from the battery and its service
life may be shortened.
Therefore, even when not in regular
use, it is recommended that the unit be
recharged at least every six month.
[ER2031]
Nickel‑Cadmium battery is contained.
When you are no longer able to use
your trimmer after consulting dealers
and decide to discard it, make sure
that the battery is disposed of at an
officially assigned location, if there is
one in your country.
[ER2051]
Nickel‑Metal Hydride battery is
contained.
When you are no longer able to use
your trimmer after consulting dealers
and decide to discard it, make sure
that the battery is disposed of at an
officially assigned location, if there is
one in your country.
How to remove the built‑in
rechargeable battery before
disposal of the trimmer
(See Fig. 7, 8)
The battery in this trimmer is not
intended to be replaced by consumers.
However, the battery may be replaced
at an authorized service center.
The procedure described below is
intended only for removal of the
rechargeable battery for the purpose of
proper disposal.
Always make sure that the battery has
been removed from the trimmer before
disposing of it.
[ER2031]
1. Disconnect the power cord from the
AC outlet, and remove the power
cord (K) from the trimmer.
2. Remove the comb attachment (F)
To Next Page
Loading...
