Panasonic EY7441 - Intended Use and Safety

- 5 -
Original instructions: English
Translation of the original instructions:
Other languages
This tool, as a complete unit with a battery
pack, satisfies appropriate IP Degrees of
Protection based on the IEC regulations.
'H¿QLWLRQRI,3FRGH
IP5X: Ingress of dust is not totally
prevented, but dust shall not penetrate
in a quantity to interfere with satisfactory
operation of the tool or to impair safety
(In case that the talcum powder under 75
ȝPLQWUXGHVLQVLGHWKHWRRO,3;:DWHU
projected in powerful jets against the tool
from any direction shall have no harmful
effects (In case that, with a nozzle of
12.5 mm inner diameter, approximately
100 L/min of normal temperature water is
injected to the tool for 3 minutes from 3
PHWHUGLVWDQFH
/,0,7(':$55$17<
7KHUDWLQJRI,3TXDOL¿HVWKLVWRROIRUWKH
minimum impact of water or dust, but not
for the assurance of performance in such
conditions. See Safety and Operating
Instructions for further details for proper
operation.
,,17(1'('86(
7KHVHWRROVFDQEHXVHGWRWLJKWHQ
VFUHZVLQFOXWFKPRGHDQGWRGULOO
KROHVLQZRRGDQGPHWDOLQGULOOPRGH
$GGLWLRQDOO\PRGHO(<FDQEH
XVHGWRGULOOKROHVLQVRIWFRQFUHWHDQG
VLPLODUPDWHULDOVLQKDPPHUPRGH
5HDGWKH6DIHW\,QVWUXFWLRQVERRNOHW
DQGWKHIROORZLQJEHIRUHXVLQJ
,,$'',7,21$/
6$)(7<58/(6
 :HDUHDUSURWHFWRUV
Exposure to noise can cause hearing
loss.
 8VHDX[LOLDU\KDQGOHVXSSOLHGZLWK
WKHWRRO
Loss of control can cause personal
injury.
 +ROGSRZHUWRROVE\LQVXODWHG
JULSSLQJVXUIDFHVZKHQSHUIRUPLQJ
DQRSHUDWLRQZKHUHWKHFXWWLQJWRRO
PD\FRQWDFWKLGGHQZLULQJ contact
with a “live” wire will make exposed
metal parts of the tool “live” and shock
the operator.
 :HDUDGXVWPDVNLIWKHZRUNFDXVHV
dust.
 %HDZDUHWKDWWKLVWRROLVDOZD\VLQDQ
operating condition, since it does not
have to be plugged into an electrical
outlet.
 :KHQGULOOLQJRUGULYLQJLQWRZDOOV
ÀRRUVHWF³OLYH´HOHFWULFDOZLUHVPD\
be encountered. DO NOT TOUCH
THE CHUCK OR ANY FRONT METAL
PARTS OF THE TOOL! Hold the tool
only by the plastic handle to prevent
electric shock in case you drill or drive
into a “live” wire.
 ,IWKHELWEHFRPHVMDPPHG
immediately turn the trigger switch
off to prevent an overload, which can
damage the battery pack or motor.
Use reverse motion to loosen jammed
bits.
 'R127RSHUDWHWKH)RUZDUG5HYHUVH
lever when the trigger switch is on.
The battery will discharge rapidly and
damage to the unit may occur.
 'XULQJFKDUJLQJWKHFKDUJHUPD\
become slightly warm. This is normal.
Do NOT charge the battery for a long
period.
 :KHQVWRULQJRUFDUU\LQJWKHWRRO
set the Forward/Reverse lever to the
FHQWHUSRVLWLRQVZLWFKORFN
 'RQRWVWUDLQWKHWRROE\KROGLQJWKH
speed control trigger halfway (speed
FRQWUROPRGHVRWKDWWKHPRWRUVWRSV
 'R QRWRSHUDWHWKHVSHHGVHOHFWRU
VZLWFK/2:+,*+ZKLOHSXOOLQJRQ
the speed control trigger. This can
cause the rechargeable battery to
wear quickly or damage the internal
mechanism of the motor.