When this type
of editing
is
done,
the
picture
and
the
sound
are
recorded
on the tape as shown below. However, if no
new sound is input, the original sound remains only
on
the
"normal" audio
track
ot
the tape
because the original Hi-Fi
sound
will
always be erased during insert editing.
By
performing
insert editing togelher with
audio dubbing,
the
sound on
the
"normal"
audio track can also be replaced
at the same time.
Video
and
Audio Track Recordinq
Pattern
"Normal"
Audio
Track Original
Sound
Video Tracks
(lnserled
Picture)
Hi-FiAudio
Tracks
(lnserted
Sound)
Preoaration
.lnsert
a
video
cassette with the erasure
prevention
tab
intact.
.When
performing
insert
editing
from
another VTR, set the
Noise Filter/Edit
Selector to
"EDIT
ON".
.Set
the Input Signal Selector
according
to
the type of
insert
editjng
to
be
performed.
"Line/Audio"; When inserting
picture
and sound lrom
equipment
connected
to the Video lnput
Socket and
the Audio Inout
Sockets on
the
rear ot this VTR.
"Tuner":
When inserting scenes from a TV
pro-
gramme.
(O
Press the Jog/Shuttle
Button.
€)
Use the Shuttle Ring
and the Jog Dial to
search
lor the
point
where
you
want the
editing to end
(end
point),
and
putthe
VTR into
the still
playback
mode.
@
Press the Resevlndex Button
(Remote
Controller) to
reset
the
TaDe
Counter to
"0;00.00".
Use
the
Shuttle
Ring
and
the Jog Dial to search Ior the
point
where
you
want the editing to start
(start point),
and
put
the
VTB into
the still
playback
mode.
Press the Memory/Repeavsearch Button on the
Remote Controller so that the Memorv Indicator
"M"
mark will light up.
Press the Insert Editing Button.
(The
Insert Editing
Indicator lights up.)
ll
you
want to replace the sound on the "normal" audio
track, too,
press
the Audio Dubbing Button.
(The
Audio Dubbing indicator lights up.)
After the
picture
to be inserted is
prepared, press
lhe
Pause/Still Button
(l
l).
(The insert
editing will start.)
.The
insert editing will
end at
the
point
where the Tape
Counter
indicales
"0:00.00",
and the editing VTR
will
stop in the still
playback
mode.
The sound inserted during insert editing is recorded on
the
Hi-Fi sound tracks
(STEBEO,
LEFT,
RIGHT). lf the normal
sound track is selected, the original sound before the
insert
editing
will
be
heard.
Select
the desired sound with lhe
Audio Output l\4ode Selector
(Remoie
Controller).
Hi-Fi/Normal Mix
Switch
Set this switch to
"On",
if
you
want both the "Hi-Fi" sound
and the
"normal"
sound to be
played
back mixed together.
.The
mixed sound may
not
be
very
clear.
Always set this switch to
"Oll",
except when
playing
back
a tape on which
the insert
editing or audio dubbing
was
oerformed.
.The
picture quality
of an
inserted
part
is
always
somewhal
inferior to
that of the original.
.Avoid
performing
insert editing repeatedly on the
same
part
of the tape
because
the
picture
quality
of
that
part
becomes inlerior.
.The
inserted
picture
may
contain slight colour
noise
or
lhe
colours may be unstable.
.Do
not
press
the Memory/Repeavsearch
Button
during insert editing. lf it is
pressed,
the lvlemory
Indication
"M"
will
disappear, and
the insert
editing
will not
end automatically at the
preset
editing end
Doint.
.lt
is not necessary
to operate the Tape
Speed
Selector.
@
o
@
o
-EE-ddddEt=Ea
EE
EE
,^t
oa
-
o()v;
RESET4NDEX
<41)
To Next Page
Loading...
