Panasonic Omnivision PV-8451 - VCR Plus+ Programming

j*f« YC^Plus^Programminj
Easy Taping.
Check list before you begin.
□ The clock is set.
□ VCR Plu$+ Setup is complete
(see pages 28-30).
Multi Function Display
ffeT
©X.GE) .A?
_o © ©
© © ©
© Q |
■ S 0 0!
%m ix® ccutrw awor
9°flQ
■ A DD/
DELETE
Use normal Timer Recording steps if:
• the PlusCode for a program is not listed.
• you anticipate the program, such as a sporting
event, to run over the scheduled stop time.
See page 19 to:
• cancel a timer recording in progress.
• replace program contents.
• review or clear program contents once set.
Important notes when using a DSS receiver
• When recording programs via a DSS receiver,
the DSS receiver must be left on.
• When recording programs via an antenna or
cable, the DSS receiver must be turned off.
Press PROG to display the
“SET PROGRAM” screen.
2 Press AT to select “VCR Plus+
PROGRAM,” and then press ►
to display the “VCR Plus+” screen.
3 Press the NUMBERED keys to
enter the PlusCode number.
• Refer to your local TV listings.
SET PROGRAM
TIMER PROGRAM _
VCR Plus*
ENTER PLUSCOOE NUMBER
\ I /
/ I v
USING 0-9 KEYS
VCR Ptus+
ENTER PLUSCODE NUMBER
123456
USING 0-9 KEYS
To Make Corrections backspace : « key
Press A repeatedly to delete the enter :prog key
PlusCode number. Then, enter the correct number.
Press PROG to lock in your program.
5 Press the 1, 2 or 3 key to select
VCR Plus*
the program type.
1 ONE TIME
2 DA 1LY (MON-FR1)
3 WEEKLY
6 Press AT and ► to select and
TO SELECT PUSH 1.2 OR 3
DATE START STOP CH
set each of the remaining items
as follows.
TOO AY tee*
Remaining Items
CATEGORY :(HH S 1
• Category (N/A [not applicable], SPORTS,
MOVIE, COMEDY, MUSIC, DRAMA)
SELECT:A ▼ KEY
SET H ► KEY
• Speed (SP, LP. SLP)
END :PROG KEY
To Make Corrections
Repeatedly press ► to move the cursor
to the right, or M to move to the left to the
incorrect entry and make the correction.
7 Press PROG if contents are
acceptable.
To cancel program contents:
Press ADD/DELETE.
8 Press PROG to complete
the program.
• If you're using a Cable Box, make sure
that it is tuned to the desired channel
and the power is left on for timer recording.
“A" on page 28, the
channel shown in this on¬
screen display will always
be the cable box output
channel number.
P DT start stop ch spd
1 DAY 9:OOA12:OOA 06 SPl
CANCEL:ADD/DLT KEY
SELECT 1-8:A ▼ KEY
ENTER : ► KEY
END :PR0G KEY
TURN VCR OFF
FOR TIMER RECORDING
AND
LEAVE CABLE BOX POWER ON
This display may differ depending
on your cable box hook-up.
Press POWER off to set the timer.
Multi Function Display
— • You can obtain unlisted PlusCode numbers by calling 1 - 900 - 454 - 7587. Call costs approximately $.95
f per minute.
[NOTES) * VCR PlusCodes can not be used to program the VCR to record DSS channels,
r J • Avoid overlapping program times.
^• An on-screen display will indicate if an invalid PlusCode number has been entered or when all timer
programs are full.
More
You
Can
Do