Panasonic Omnivision PV-C1331W

Before Requesting Service
Check the following points once again if you are having trouble with your unit.
Power
Orel aasteiitels
No power... * Completely insert Power Plug into an AC outlet.
« Set POWER button to ON.
Monitor
No picture or sound...
Poor picture with normal sound...
Poor sound with normal picture...
Poor TV reception...
No color or r color...
Ghost (multiple) images...
TV programs cannot be watched...
Channel cannot be selected...
TV program cannot be recorded...
Timer recording cannot be
performed...
No playback picture, or the playback
picture is noisy or contains streaks...
VCR cannot ry controlled...
aiclaile) im Ove) aliae):
Unit cannot be controlled...
ACTION, PROG and FWTV
buttons cannot be selected...
WWiikvexsiiblasveler
Video cassette cannot be
inserted...
Video cassette cannot be
removed...
Tape cannot be ejected or
inserted...
Video cassette ejects when a
recording is started, or the power
is tumed off for timer recording...
In Stop mode, the VCR motor
(CYLINDER) continues to rotate...
VCR cannot be controlled...
@felga-rerdtela
Make sure your antenna m {TV or CABLE), is correctly set. (P. 8-11)
Completely insert Power Plug into an AC outlet.
Set POWER button to ON.
Adjust BRIGHTNESS, SHARPNESS, and PICTURE controls in the
SET UP TV menu. (P. 20)
Adjust VOLUME control. (P. 16)
Adjust SHARPNESS and PICTURE controls in the SET UP TV menu. (P. 20)
Adjust TINT and COLOR controls in the SET UP TV menu. (P. 20)
Install a directional antenna.
Make sure the selected channel is in unit's memory. (P. 12-13)
Only the channel being recorded can be viewed on this unit.
(Ofelaastoittela
Make sure your antenna system (TV or CABLE), is correctly set. (P. 8-11)
Make sure cassette record tab is intact. (P.4)
Check that clock is set to current time and date.
Make sure DSS/CABLE box (if used) is left on and tuned to channel! to
be recorded.
Set recording Start/Stop times correctly. (P. 22-23)
Timer may not be performed or continued if a power
interruption of more than 1 minute occurs before or during a Timer
recording even after power is restored.
Adjust TRACKING control in either direction. (P. 37)
Try Head Cleaning. (P. 37)
Make sure VCR LOCK is set to off. (P. 27)
Make sure unit is not in a Timer Record operation.
Correction
Aim remote at remote sensor on unit (P. 7) so that signal is
unobstructed
Inspect the remote batteries. (P. 4)
Make sure VCR LOCK is set to off. (P. 27)
Exposing unit remote sensor to direct fluorescent or outdoor light may
cause signal interferance.
Check remote batteries.
Correction
Insert the cassette window side up; record tab facing you.
Completely insert Power Plug into an AC outiet.
Ms Patil or inserting the tape again after tuming POWER off, then
ack on
Make sure cassette record tab is intact. (P. 4)
To enable Quick Play mechanism, the VCR cylinder will rotate for
about 3 minutes. This reduces response time from Stop to Play mode
and from Play to Rewind Search mode. —-
Make sure VCR LOCK is set to off. (P. 27)
lf you cannot resolve the problem, please caii the Customer Satisfaction Center for
product assistance at 201-348-9090.
To locate an authorized servicenter call tol! free 1-800-211-PANA(7262)
or send e-mail to : consumerproducts@ panasonic.com.
38 For assistance. please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts @ panasonic.com