Panasonic S-50PK1E5A - Page 17

29
"LINKINGh
” indicator
Cancel
Auto address
1
Assigning
Display During Auto Address Setting ●
On the surface of outdoor unit control P.C. board
1
2
,%$ "LINKSALTERNATELY
 $ONOTSHORTCIRCUITTHE!!$$PINAGAINDURINGAUTOADDRESSSETTING
,%$SANDGOOUTANDADDRESSSETTINGISINTERRUPTED
 7HENAUTOADDRESSSETTINGISNORMALLYCOMPLETEDBOTH,%$SANDGOOUT
In other cases, correct settings referring to the following table and perform auto address setting again.
●
 #ONTENTSOF,%$SANDONOUTDOORUNITCONTROL0#BOARD
: ON "LINKING  : OFF
,%$ ,%$ Remark
Normal operation 0RETRIP(IGHPRESSUREPROTECTION ,%$"LINKINGSEC/.SEC/&&
Pre-trip (other)
,%$"LINKINGSEC/.SEC/&&
Auto address setting
Under auto address setting
"LINKINGALTERNATELY
Auto address setting alarm
Follow the blinking patterns of each alarm
!LTERNATEBLINKINGOFOUTDOORUNIT,%$ during alarms
,%$BLINKS-TIMESANDTHEN,%$BLINKS.TIMES4HECYCLETHENREPEATS -0ALARM(ALARM%ALARM&ALARM,ALARM.ALARM.O %XAMPLE,%$BLINKSTIMESTHEN,%$BLINKSTIMES4HECYCLETHENREPEATS!LARMISh%v
Power ON sequence
No communication from indoor units in system
If it is not possible to advance to 3 repeats 1
→
2
Communication received from 1 or more indoor units in system
At 3, advances to normal control
2EGULARCOMMUNICATION/+ (Capacity and unit quantity match)
Refrigerant recovery mode
●
 $ISPLAYOFREMOTECONTROLLER
CZ-RTC5A CZ-RTC4
30
8-9. Indicating (marking) the indoor and outdoor unit combination number Indicate (mark) the number after auto address setting is completed. ●
So that the combination of each indoor unit can be easily checked when multiple units are installed, ensure that the indoor and
OUTDOORUNITNUMBERSCORRESPONDTOTHESYSTEMADDRESSNUMBERONTHEOUTDOORUNITCONTROL0#"ANDUSEAMAGICMARKERORSIMILAR means which cannot be easily erased to indicate the numbers in an easily visible location on the indoor units (near the indoor unit nameplates). Example: (Outdoor) 1 - (Indoor) 1
(Outdoor) 2 - (Indoor) 1
●
These numbers will be needed for maintenance.
"ESURETOINDICATETHEM
Use the remote controller to check the indoor unit address. High-spec Wired Remote Controller (CZ-RTC5A)
(3)4HEh3IMPLESETTINGSvSCREENAPPEARSONTHE,#$DISPLAY
Select the “Unit no.” by pressing the
or
button for changes.
Simple settings
Unit no. Code no. Set data
01
3-1 0001
Sel. Next
20:30 (THU)
The indoor unit fan operates only at the selected indoor unit.
START
[]
20:30 (THU)
Timer remote controller (CZ-RTC4) <If 1 indoor unit is connected to 1 remote controller> (1) Press and hold the
button and
button for 4
seconds or longer (simple settings mode).
(2) The address is displayed for the indoor unit that is
connected to the remote controller.
( Only the address of the indoor unit that is connected to
the remote controller can be checked.)
(3) Press the
button again to return to normal remote
controller mode.
Number changes to indicate which indoor unit is currently selected.
Indoor unit address
(1) +EEPPRESSINGTHE ,
and buttons
simultaneously for 4 or more seconds. 4HEh-AINTENANCEFUNCvSCREENAPPEARSONTHE,#$ display.
Maintenance func
1. Outdoor unit error data 2. Service contact 3. RC setting mode 4.Test run
Sel. Page [ ] Confirm
20:30 (THU)
(2) Press the or button to see each menu.
If you wish to see the next screen instantly, press the
or button.
3ELECTh3IMPLESETTINGSvONTHE,#$DISPLAYANDPRESS the
button.
Maintenance func
5. Sensor info. 6. Servicing check 8. Detailed settings
Sel. Page [ ] Confirm
20:30 (THU)
7. Simple settings
17
ENGLISH
00_2WAY_All_282008.indb 1700_2WAY_All_282008.indb 17 2016/12/1 9:55:192016/12/1 9:55:19