Panasonic S-50PY2E5A - Page 15

25
8-5. Test Run Using the Remote Controller High-spec Wired Remote Controller (CZ-RTC5A) (1) +EEPPRESSINGTHE
,
and buttons
simultaneously for 4 or more seconds. 4HEh-AINTENANCEFUNCvSCREENAPPEARSONTHE,#$ display.
Maintenance func
1. Outdoor unit error data 2. Service contact 3. RC setting mode 4.Test run
Sel. Page [ ] Confirm
20:30 (THU)
(2) Press the or button to see each menu.
If you wish to see the next screen instantly, press the
or button.
3ELECTh4ESTRUNvONTHE,#$DISPLAYANDPRESSTHE
button.
Maintenance func
1. Outdoor unit error data 2. Service contact 3. RC setting mode 4.Test run
Sel. Page [ ] Confirm
20:30 (THU)
Change the display from OFF to ON by pressing the
or button. Then press the button.
[ ] Confirm
Test run
Change
20:30 (THU)
Test run
ON
START
[]
20:30 (THU)
(1)
(1)
(4)
(3) Press the button. “TEST” will be displayed on the
,#$DISPLAY
TEST
START[]
20:30 (THU)
(4) Press the button. Test run will be started.
4ESTRUNSETTINGMODESCREENAPPEARSONTHE,#$DISPLAY
TEST
20:30 (THU)
COOL
MODE
Timer remote controller (CZ-RTC4) (1) Press the remote controller
button for 4 seconds or longer.
Then press the
button.
●
“
vAPPEARSONTHE,#$DISPLAYWHILETHETESTRUNISINPROGRESS
●
The temperature cannot be adjusted when in Test Run mode.
(This mode places a heavy load on the machines. Therefore use it only when performing the test run.)
(2)4HETESTRUNCANBEPERFORMEDUSINGTHE(%!4#//,OR&!.
operation modes.
NOTE
The outdoor units will not operate for approximately 3 minutes after the power is turned ON and after operation is stopped.
(3) If correct operation is not possible, a code is displayed on the remote
CONTROLLER,#$DISPLAY (3EETHESECTIONh4ABLEOF3ELF$IAGNOSTIC&UNCTIONSAND Corrections” and correct the problem.)
(4) After the test run is completed, press the
button again.
Check that “
vDISAPPEARSFROMTHE,#$DISPLAY
(To prevent continuous test runs, this remote controller includes a timer function that cancels the test run after 60 minutes.) * If the test run is performed using the wired remote controller, operation
is possible even if the cassette-type ceiling panel has not been installed. (“P09” display does not occur.)
26
8-6. Precautions ● Request that the customer be present when the test run is
performed. At this time, explain the operation manual and have the customer perform the actual steps.
● "ESURETOPASSTHEMANUALSANDWARRANTYCERTIFICATETOTHE
customer.
● Check that the 220 – 240 V AC power is not connected to
the inter-unit control wiring connector terminal. * If 220 – 240 V AC is accidentally applied, the indoor or
OUTDOORUNITCONTROL0#"FUSEWILLBLOWINORDERTOPROTECT THE0#"#ORRECTTHEWIRINGCONNECTIONS2EMOVETHE short connector connected to the OC side and reconnect TOTHE%-'SIDEONTHEOUTDOORCONTROL0#"#UTTHE3! OUTOFTHEOUTDOORUNITCONTROL0#"4HENDISCONNECTTHE 2P connectors (OC) that are connected to the indoor unit 0#"ANDREPLACETHEMWITH0CONNECTORS%-' If operation is still not possible after changing the brown connectors, cut off the jumper (indoor unit) or the varistor INDOORUNITONTHE0#""ESURETOTURNTHEPOWER/&& before performing this work.)
/UTDOORUNITCONTROL0#"
CN-EMG
SA1
)NDOORUNITCONTROL0#"
■
Type U2
Jumper (JP040)
EMG (CN044, brown)
OC (CN040, blue)
■
Type T2
Jumper (JP040)
EMG (CN044, brown)
OC (CN040, blue)
Jumper (JP040)
OC (CN040, blue)
EMG (CN044, brown)
■
Type F1
OC (CN040, blue) Jumper (JP003) EMG (CN044, brown)
■
Type N1
■
Type Y2
OC (CN040, blue)
EMG (CN044, brown)
Jumper (JP003)
■
Type K1
Jumper (JP003) EMG (CN044, brown) OC (CN040, blue)
15
ENGLISH
00_2WAY_All_282008.indb 1500_2WAY_All_282008.indb 15 2016/12/1 9:55:172016/12/1 9:55:17