Panasonic SC-HC37

13
RQT9640
Listening to FM/AM radio
You can preset up to 30 FM channels / 15 AM
channels.
Preparation
Make sure that the antenna(s) are connected. (> 8)

A station previously stored is overwritten when another station
is stored in the same channel preset.
1 Press [RADIO] to select “FM” or “AM”.
2 Press [PLAY MENU] repeatedly to select
“A.PRESET” and then press [OK].
3 Press [3, 4] to select “LOWEST” or “CURRENT”
and then press [OK].
LOWEST:
To begin auto preset with the lowest frequency
(FM 87.50, AM 520 or AM 522).
CURRENT:
To begin auto preset with the current frequency.*
* To change the frequency, refer to “Manual tuning and
presetting”.
The tuner starts to preset all the stations it can receive
into the channels in ascending order.
Preparation
1 Press [RADIO] to select “FM” or “AM”.
2 Press [PLAY MENU] repeatedly to select
“TUNEMODE” and then press [OK].
3 Press [3, 4] to select “PRESET” and then press
[OK].
1 Press [RADIO] to select “FM” or “AM”.
2 Press [:/6] or [5/9] to select the
channel.
∫ Manual tuning and presetting
Select a radio broadcast.
1 Press [RADIO] to select “FM” or “AM”.
2 Press [PLAY MENU] repeatedly to select
“TUNEMODE” and then press [OK].
3 Press [3, 4] to select “MANUAL” and then press
[OK].
4 Press [:/6] or [5/9] to tune to the
required station.
≥ To start automatic tuning, press and hold [:/6],
[5/9] until the frequency starts scrolling. Tuning
stops when a station is found.
To preset the channel
5 While listening to the radio broadcast
Press [OK].
6 Press [3, 4] to select the channel and then press
[OK].
∫ To improve FM sound quality
1 While receiving FM broadcasts, press
[PLAY MENU] repeatedly to select “FM MODE”
and then press [OK].
2 Press [3, 4] to select “MONO” and then press
[OK].
≥ This setting can be preset and memorised. To do so,
continue to step 5 of “Manual tuning and presetting”.

≥ Select “STEREO” in step 2 to return to stereo broadcasts.
≥ “MONO” is cancelled if the frequency is changed.
≥ If “MONO” is selected, regardless of the type of signal this
unit is receiving, “FM MONO” is displayed. (> below)
∫ To display the current FM signal status
While receiving FM broadcast, press [DISPLAY].

“STEREO” is displayed when this unit tunes to a stereo
broadcast.
Internet Radio
This unit can output Internet radio if “vTuner for
Panasonic” is installed on your iPhone/iPod touch.
Preparation
≥ Install “vTuner for Panasonic” to your iPhone/iPod
touch.
≥ Install iOS 5.0 or later.
1 Insert the iPhone/iPod touch to this unit.
2 Press [iPod] repeatedly to select “VTUNER”.
{. “vTuner for Panasonic” starts.

≥ Visit the below website for the following information about
“vTuner for Panasonic”:
http://radio.vtuner.com/panasonic/en/
(Compatible iPhone/iPod touch models and software
versions, purchasing, installation and operation details.)
≥ A pop-up screen may appear on your iPhone/iPod touch.
Follow the indicated instructions.
AM radio is only available for [SC-HC37]
Presetting stations
automatically
Listening to a preset channel
“FM ST”: The FM signal is in stereo.
“FM”: The FM signal is in monaural.
≥ “FM” is also displayed even if this unit is not tuned to a
station.
SC-HC37DBGN_37GN~RQT9640-1L.book Page 13 Tuesday, February 28, 2012 11:30 AM