Panasonic UJ30 Series

Questions and Answers

C
charlotteonealAug 14, 2025
What to do if the interlock contact opens during Panasonic UJ30 Lighting Equipment irradiation?
- A
  Ashley AguilarAug 14, 2025
  If the emergency stop contact opens during irradiation, check the emergency stop contact or the external input terminal block. Close the contact and then restart irradiation. If the emergency stop contact is open, normal resetting is not available. Hold down SET to forcibly reset the interlock.
H
Harold PinedaAug 17, 2025
What to do when my Panasonic UJ30 shows an LED time error?
- C
  Carrie DominguezAug 17, 2025
  If the total irradiation time of the LED reaches the preset LED replacement point (or if the LED replacement point was set ahead of the total irradiation time), reset the error status, replace the LED head, and then clear the total irradiation time. Alternatively, go to the mode setting screen and correctly set the LED replacement point.
C
Christina HobbsAug 20, 2025
What to do if my Panasonic Lighting Equipment shows a connection error during irradiation?
- S
  Sandra SchmidtAug 20, 2025
  If the LED was disconnected during irradiation, it is possible that the connection cable or LED head was broken. Reset the error status, check the connection of the cable and LED head with the channel in question, and replace them if necessary.
D
Denise ZimmermanAug 25, 2025
What causes an LED temperature error in Panasonic Lighting Equipment?
- F
  Frank JohnsonAug 25, 2025
  An LED temperature error occurs because the LED temperature exceeded the upper limit. To fix this, set the UV intensity level (%) lower or improve the heat radiation performance of the LED head to keep the temperature lower than the warning level.
B
Brandon MillsAug 27, 2025
What causes a broken LED wire error in Panasonic UJ30?
- C
  Christopher MarquezAug 27, 2025
  If an LED circuit opening was detected during irradiation, it is possible that the connection cable or LED head was broken. To resolve this, reset the error status, check the connection of the connection cable and LED head with the channel in question, and replace them if necessary.
D
dperezAug 30, 2025
What should I do if my Panasonic Lighting Equipment LED is short-circuited?
- A
  Andre BryantAug 30, 2025
  If LED short-circuiting was detected during irradiation, it is possible that the connection cable or LED head was short-circuited. Reset the error status, check the connection of the cable and LED head with the channel in question, and replace them if necessary.
M
michael61Sep 2, 2025
What does a time warning mean on my Panasonic Lighting Equipment?
- S
  Sarah WatkinsSep 2, 2025
  A time warning indicates that the total irradiation time of the LED has reached the point 30 hours before the preset LED replacement point. Prepare a new LED head. After replacement, clear the total irradiation time.
C
crystalweeksSep 6, 2025
How to fix 'Calibration uncompleted' error on Panasonic UJ30?
- C
  Charles KleinSep 6, 2025
  If calibration was stopped before completion, or if the calibration was not successful, reset the error status, check the connection of the UV sensor, review the setting, and then retry calibration.
J
James PooleSep 9, 2025
How to troubleshoot a Panasonic Lighting Equipment when the LED does not irradiate?
- W
  williamsjohnSep 9, 2025
  Select the target channel when setting the product type. If the target channel is selected but does not irradiate, check if the irradiation time is set to 0.0sec for the channel program for the target product type. If so, set the irradiation time to 0.0sec or longer.