ActionGRIP Shorty
Suction Cup Camera Mount
Low profile: Mount camera
as close to surface as possible.
Only for cameras with 1/4-20 mounting stud.
ActionGRIP
Single Knuckle
Suction Cup Camera Mount
Full articulation at the camera:
210° Tilt, 360°Turn &
360° Rotation.
ActionGRIP
Double Knuckle
Suction Cup Camera Mount
Double ball design for maximum
articulation. 210° Tilt, 360° Turn
& 360° Rotation at both ends.
Position the camera exactly
where you need it.
ACTIONGRIP 3-N-1 ACTION CAMERA MOUNT KIT
As the name implies, the 3-N-1 Action Camera Mount Kit allows you to build the 3 different Action Camera Mounts (sold separately) pictured below from this single kit. Detailed
instructions on how to assemble, use and attach your ActionGRIP 3-N-1 Action Camera Mount Kit are included in this manual. Please read them carefully. If you have any questions
about your ActionGRIP 3-N-1 Action Camera Mount Kit, either call 1-800-759-7535, (8am to 5pm Pacific Time) or email cs@panavise.com.
Model: 13101
Model: 13120
Model: 13130
BUILD
DIFFERENT
MOUNTS
FROM
ONE KIT
3
CAPTURE UNIQUE ANGLES & SHOTS
The ActionGRIP 3-N-1 Action Camera Mount Kit allows you to assemble one out of three different Action Camera Mounts, quickly and easily so you can position
your camera exactly where you want it to get that perfect camera angle and capture the action from a unique angle during your shoot. With your imagination and
this versatile kit, you can capture or shoot from just about any angle or position you can dream up.
Build an ACTIONGRIP SHORTY for shots
requiring an extreme low profile camera
angle close to the mounting surface. Ideal
for vehicle roofs, hoods, trunk lids. Camera
can be tilted forward and backwards and
rotated side to side.
Build an ACTIONGRIP SINGLE KNUCKLE when
you want the camera closer to the surface but need a
higher range of adjustment than the ActionGrip Shorty
provides. You can tilt, turn, and rotate your camera to
get your camera back to parallel even if the suction
cup is mounted at an angle to the camera plane.
Build an
ACTIONGRIP DOUBLE KNUCKLE, when you want
the camera higher or further away from the suction cup, to peer
over, around or under an obstruction in front of your camera or
for use inside of a vehicle when attached to a sloping windshield.
The ActionGrip Double Knuckle provides tilt, turn, and rotate in
two different locations for optimum positioning of your camera.
Works with GoPro’s Hero® cameras & compatible with any camera with standard 1/4-20 mounting stud. Simply change out the included ball assembly.
Thoroughly clean the smooth, flat, non-porous
mounting surface
.
The surface should be dry and free
of any scratches or debris.
Position the
Suction Cup Lever
in the “down”
position. Position the
Suction Cup
in your mounting
location. In order to remove the mount easily, PanaVise
recommends that the
Suction Cup Release Tab
be
at the bottom of the installation and that the
Mounting Arm
moves freely in a vertical line.
Push the
Suction Cup
firmly against the mounting surface
(the Suction Cup Lever should be in the “down”position).
PRESS the
Suction Cup Button
completely
.
PULL the
Suction Cup Lever
up and over the
Button
. You will
feel the
Button
move out during this procedure; this action
locks the
Suction Cup
into place.
COMPLETE
CONGRATULATIONS
on your panavise purchase!
3-N-1 Suction Cup Camera Mount Kit
Model: 13150
For questions & comments, call
1-800-759-7535
or check out our website for
product specifications and ideas:
www.pan avis e.com
VISIT US ON
Innovative Holding Solutions
ACTIONGRIP
INSTRUCTIONS:
Includes components
to make three different
ActionGrip Mounts.
ABOUT PANAVISE
Founded in 1956, PanaVise
Products, Inc. is a world lead-
ing manufacturer of high qual-
ity precision work holding
tools, CCTV camera mounts,
action sports camera mounts
and mobile electronics mounts
and accessories. PanaVise also
offers expert OEM/ODM cus-
tom mount design and produc-
tion capabilities for some of
the world’s most well-known
consumer electronics brands.
PanaVise designs and engineers
its “innovative holding solu-
tions” at its headquarters in
Reno, Nevada USA. Manufactur-
ing occurs at PanaVise facilities
in Reno and Changzhou.
INSTALLING SUCTION CUP MOUNT TO SURFACE
NOTE
The mounting surface and the
Suction Cup should be clean and
dry. Wipe with a clean, damp
cloth and let dry completely.
The Suction Cup Mount should
be installed at room temperature
(avoid extremes of heat or cold)
. Do
not moisten the Suction Cup.
Install camera (weighing up to 3 pounds)
onto the 1/4-20
Mounting Stud
.
Hold the camera in place and tighten
the
Lock Ring
firmly.
NOTE: Review your camera’s manual
for mounting stud length requirements.
To release the
Suction Cup
, move
the Suction Cup Lever back into its
“down”position. Lift the
Suction Cup
Release Tab
to help break the hold.
6
1 2 3 5 64
1
2
3
4
5
6
INSTALL YOUR CAMERA
REMOVE SUCTION CUP
ACTION CAMERA MOUNTS
WHICH
ActionGRIP
CAMERA
MOUNT
DO I USE ?
To Next Page
Need help?
General