Panther PA-620C - User Manual

1
128-9107
1 of 8
Model PA-620C
Owner’s Manual
KEYLESS ENTRY OPERATION
The Lock button on the transmitter is used to lock the vehicle's doors, the Unlock button is
used to unlock the vehicle's doors. To lock or unlock the doors simply press and release the
desired function button one time. For your convenience, when the doors are locked, the
parking lights will flash and the horn will beep one time. When the doors are unlocked the
parking lights and or vehicle horn will flash/beep twice.
REMOTE CAR FINDER
The Lock or Unlock buttons are also used to access the car finder mode. This feature is
particularly useful in a crowded parking lot where finding your car may be difficult. To
access the car finder mode, while within range of your car, simply press and hold either the
lock or unlock button of your transmitter for three seconds. The parking lights will begin to flash, and if
connected, the vehicle horn will beep making your vehicle audible as well as more visible. The lights
and or horn will stop automatically after 30 seconds. If you wish to turn off the car finder mode prior to the
expiration of the 30 second timer, press and hold for three seconds either the lock or unlock buttons a second
time, or press and release the Trunk/Start button one time.
REMOTE TRUNK RELEASE
If you have electric trunk release in your vehicle and the remote trunk release option was added, simply
press and hold the Key/Trunk button of your keychain transmitter for 4 seconds or until the electric trunk of
your vehicle opens.
REMOTE STARTING THE VEHICLE
This unit will not start the vehicle if any one of the following situations exists;
The vehicle's hood lid is opened. The gear shift selector is not in Park.
The brake pedal is depressed. The system is placed in the override position.
1. To start the vehicle, press and release the Key/Trunk button two times within 2 seconds. The vehicle will
start and remain running for the pre-programmed 5,10,15,20 minute run cycle. As a visual indication, the
parking lights will flash or remain on depending on the setting by your installation center.
2. When you arrive at the vehicle, turn the ignition key to the ON position (not the spring loaded start position),
then step on the brake pedal to disengage the remote starter. The vehicle will continue to run, but now on
it's own power.
NOTE: The engine will stop running before the pre-programmed run cycle has expired if you perform any
one of the following functions;
Press and release Key/Trunk button on the keychain transmitter two times within 2 seconds.-Depress
the brake pedal. - Open the vehicle's hood -Place the unit in the safety control disabled mode.
THE OPTION BUTTON of your transmitter may or may not be used with your system but may be used with
a second similar Audiovox Model system that may be installed on a second vehicle in your family.
PUSH-BUTTON SAFETY CONTROL/PROGRAM SWITCH
The Push-Button safety control switch allows you to temporarily disable the remote starting function of the
system. This is recommended whenever the vehicle is being serviced. To place the system in the service/
temporary disabled mode:
1) With the system disarmed/unlocked, and the ignition switch off press and hold the override/program Push-
Button Switch on.
2) Turn the ignition switch on, off, on, off, on, off.
3) The LED begins to flash two short flashes followed by one long flashes and continues this pattern until
returned to normal mode of operation.
This puts the unit into the R/S Override mode indicating that the remote start system is in the service/
temporary disabled mode and will not start from RF or any other input Telematic input or otherwise.
To Exit R/S Override Mode:
1) With the system disarmed, press and hold the Push-Button Switch on.
2) Turn the ignition switch on, off, on, off, on, off.
3) The LED turns off indicating that the R/S unit is fully functional once again.

Summary

Remote Start and Security Functions

Keyless Entry Operation

Operate door locks using transmitter buttons; visual/audible feedback provided.

Remote Car Finder

Locate vehicle in crowded areas using flashing lights and horn beeps.

Remote Trunk Release

Open the vehicle's electric trunk by pressing and holding a specific transmitter button.

Remote Vehicle Starting

Start the vehicle remotely for a set run cycle; includes pre-start conditions.

Push-Button Safety Control;Program Switch

Temporarily disable remote start function for service via a push-button switch.

Automatic Start Up Timer Mode

Initiating Automatic Start Timer

Activate scheduled engine starts to maintain vehicle warmth using specific transmitter commands.

Canceling Automatic Start Timer

Stop the automatic start sequence by manually operating the vehicle or remote starting it.

Transmitter Programming and Management

Programming New Transmitters

Procedure to add or replace transmitters for system control, up to four units.

Second Vehicle Operation

Switch between controlling primary and secondary vehicles with the transmitter.

Deleting Transmitters

Remove lost, stolen, or unwanted transmitters from the system's memory.

Maintenance and Safety Warnings

Transmitter Battery Replacement

Instructions for replacing the transmitter's internal battery, typically CR2016.

Carbon Monoxide Safety Warning

Critical safety alert regarding potential fatal fumes from running engines.

FCC Compliance Information

Details on device compliance with FCC rules for radio frequency emissions.

Panther PA-620C Specifications

General

Brand	Panther
Model	PA-620C
Category	Remote Starter
Language	English