4
S Do not put pressure on thesaw at the end of
the cut. Applying pressure can cause you to
lose control when the cut is completed.
S Stop the engine before setting the saw
down.
S Do not operate a chain saw that is dam-
aged, improperly adjusted, or not com-
pletely and securely assembled. Always
replace bar, chain, hand guard, or chain
brakeimmediately ifit becomesdamaged,
broken or is otherwise removed.
S With the engine stopped, hand carry the
chain saw with the muffleraway from your
body, and the guide bar and chain to the
rear, preferably covered with a scabbard.
CHAIN SAW SAFETY EQUIPMENT
NOTE:
In thi s sect i o n , the safe t y f eatu r e s of
the chain saw and their function are explained.
For inspection and maintenance, see instruc-
ti o ns in th e CHECKI NG, MAI NTAINING AND
SERVICING CHAIN SAW SAFETY EQUIP-
MENT section. See instructions under the
WHAT IS WHA T? section, to find where these
parts are located on your chain saw . The life
span of the machine can be reduced and the
risk ofaccidents can increase ifmachine main-
tenance is not carried out correctly and if ser-
vice and/or repairs are not carried out profes-
sionally . If you need further information, please
contact your nearest service dealer .
S Chain brake. Your chain saw is equipped
with a chain brake that is designed tostop
the chain from moving.
WARNING: The chain brake is de-
signed to stop the chain immediately if you
get a kickback.The chainbrake reduces the
risk of accidents, but only you can prevent
them.DONOTASSUMETHATTHECHAIN
BRAKE WILL PROTECT YOU IN THE
EVENT OF A KICKBACK.
S Throttle trigger lock--out. The throttle
lock--out is designed to prevent accidental
operation of the throttle trigger .
S Chain catcher. The chain catcher is de-
signed to catch the saw chain if it breaks.
S Vibration damping system. Your chain
saw is equipped with a vibration damping
systemthatisdesignedto minimizevibra-
tion and make operation easier.
SAFETY NOTICE:Exposure to vibrations
through prolonged use of gasoline powered
hand tools could cause blood vessel or nerve
damageinthefingers,hands,and joints ofpeo-
ple prone to circulation disorders or abnormal
swellings. Prolonged use in cold weather has
been linked to blood vessel damage in other-
wise healthy people. If symptoms occur such
as numbness, pain, loss of strength, change in
skin color or texture, or loss of feeling in thefin-
gers, hands, or joints, discontinue the use of
this tool and seek medical attention. An anti-
vibration systemdoes notguarantee theavoid-
ance of these problems. Users who operate
power tools on a continual and regular basis
must monitor closely their physical condition
and the condition of this tool.
S ON/STOP switch. The ON/STOP switch
should be used to stop the engine.
CHECKI NG, MAINTAININ G AND
SER VI CI NG CHAIN SAW SAFETY
EQUIPMENT
WARNING: Never use a chain saw
with defective safety equipment. Safety
equipment must be inspected and main-
tained. If your chain saw does not pass in-
spection, take the saw to your nearest ser-
vice dealer for repair.
S Chain brake. Brush off any wood dust,
resin and dirt from the chain brake and
clutch drum. Dirt and wear can impair op-
eration of the brake. For additional infor-
mation, see OPERATING YOUR UNIT
section.
S Throttletriggerlock--out. Checkthatthe
throttletrigger cannotbeoperateduntilthe
throttle lock--out is pressed.
S Chain catcher. Check that the chain
catcher is not damaged and is firmly at-
tached to the body of the chain saw .
S Vibration damping system. Regularly
check the vibration damping units for
cracks or deformation. Make sure the
vibration damping units are securely at-
tached to the engine unit and handle unit.
S ON/STOP switch. Start the engine and
make sure the engine stops when you
move the ON/STOP switch to the STOP
position.
MAINTA IN YOUR SAW IN GOOD
WORKING ORDER
S Haveallchainsaw serviceperformed bya
qualifiedservice dealer with theexception
of the items listed in the maintenancesec-
tionofthismanual. Forexample,ifimprop-
er tools are used to remove or hold the fly-
wheelwhenservicingtheclutch,structural
damage to the flywheel can occur and
cause the flywheel to burst.
S Make certain the saw chain stops moving
when the throttle trigger is released. For
correction, refer to CARBURETOR AD-
JUSTMENTS.
S Never modify your saw in any way. Use
only attachments supplied or specifically
recommended by the manufacturer.
S Keepthehandles dry,clean, andfree of oil
or fuel mixture.
S Keep fuel and oil caps, screws, and fas-
teners securely tightened.
S Use only Partner accessories and re-
placement parts as recommended.
HANDLE FUEL WITH CAUTION
S Do not smoke while handling fuel or while
operating the saw.
S Eliminate all sources of sparks or flame in
the areas where fuel is mixed or poured.
Thereshouldbenosmoking,openflames,
orworkthat couldcausesparks. Allowen-
gine to cool before refueling.
S Mix and pour fuel in an outdoor area on
bare ground; store fuel in a cool, dry, well
ventilated place; and use an approved,
marked container for all fuel purposes.
Wipe up all fuel spills before starting saw.
S Move at least 10 feet (3 meters) from fuel-
ing site before starting engine.
To Next Page
Loading...
