This document describes a USB Multi-Color LED Strip, available under item numbers 86807, 86808, and 86809 from PartyFunLights.com.
Function Description:
The USB Multi-Color LED Strip is a decorative lighting product designed for indoor use. It provides multi-color illumination and various lighting effects, controlled by a remote. The LED strip can be shortened to a desired length, offering flexibility in installation. It is intended for decorative purposes and is not suitable for general space illumination.
Important Technical Specifications:
- Supply Voltage: DC 5V 2A MAX (via USB port)
- Battery Type (Remote Control): 3V, type CR2025 (button cell battery)
- Light Source: Non-replaceable LED bulbs
- Output: Supplied by an external independent LED driver with at least 5V, 2A SELV output.
- Intended Use: Indoor use only, in dry spaces.
- Electrical Classification: Classed as Electrical or Electronic equipment.
Usage Features:
- Easy Installation:
- Clean the surface where the light strip will be applied.
- Peel off the adhesive tape's backing strip.
- Press and hold the light strip firmly against the surface.
- Connectivity:
- Connect the end of the light strip to the LED/USB connector, ensuring arrows align.
- Connect the USB cable to a USB port or USB wall connection.
- Remote Control Operation:
- Power: ON/OFF switch.
- Color Selection: Control panel for various color choices, including Red, Green, Blue, and White light. Note that color settings are mixed, so colors may vary slightly.
- Light Modes:
- Brightness/Rate Adjustment: Increase/decrease brightness, or adjust the fast/slow rate in light modes.
- Shortening the Strip: The LED strip can be cut to shorten its length. It is crucial to cut only in the designated join sections and to unplug the power cord before shortening to avoid electric shock.
- Storage: After use, turn off the lights, unplug the cables, and store them in a safe place.
Maintenance Features:
- Cleaning: If the product needs cleaning, disconnect the adapter or mains cable from the power supply.
- Battery Replacement (Remote Control):
- Use a small screwdriver to remove the screw on the back of the remote control.
- Push and pull the battery compartment simultaneously to remove it.
- Replace the spent battery with a new 3V CR2025 battery, ensuring the positive terminal points upwards.
- Push the compartment back in and tighten the screw.
- WARNING: Button cell batteries can cause serious injury or death if swallowed. Dispose of used batteries immediately and safely. Keep batteries out of reach of children. Battery replacement must be done by an adult. If a child is suspected of swallowing a button cell battery, contact emergency services immediately. Ensure the battery compartment is securely fastened.
- Repair: Repairs must only be carried out by a qualified fitter or person. Do not attempt to replace connector cables yourself.
- Disposal: The product is classified as Electrical or Electronic equipment and should not be disposed of with household or commercial waste. It must be disposed of according to the Waste of Electrical and Electronic Equipment (WEEE) Directive to minimize environmental impact. Contact local authorities for information on correct disposal.
Safety Precautions and Warnings:
- Read all instructions and safety precautions carefully before use and keep them for future reference.
- Never plug the product into the mains supply while it is still in its packaging or cover it during use.
- Verify the product has not been damaged in transport before use.
- Keep the product out of reach of animals, children, and persons requiring supervision. Children may not understand the dangers of electrical equipment.
- Always place the product on a stable, solid, and flat base.
- Do not use the product near hot surfaces or objects.
- Regularly check the adapter and mains cable for damage. Do not use if damaged; repair must be done by a qualified person.
- Only use the adapter or mains cable supplied with the product.
- Never submerge the product or mains cable in water or any other liquid to prevent electric shocks, fire, or injury.
- Never carry the product by its wires, and do not wrap the cord around sharp edges.
- Do not allow the mains cable to dangle from tables/boxes.
- LED bulbs are not replaceable. If the light source reaches its end of life, the entire luminaire must be replaced.
- If light bulbs are supplied with the product, do not use them for other lighting fixtures.
- This product is not a toy.
- The external flexible cable or cord of this luminaire cannot be replaced; if damaged, the luminaire must be destroyed.
- This product flashes, which may trigger photosensitive epilepsy in susceptible individuals. Use with care.
- Never connect to DC 24V or AC 220V.
- Never connect the front and back port in case of a short circuit.
- Lead wires should be connected correctly, according to the colors on the wire.
- Do not dispose of batteries in fire.
- Adult supervision is always required when children are near any electrical appliance.
- Keep the product and cables away from water and other liquids. If the product falls into water, immediately disconnect the power supply. Do not attempt to touch or pull the product out of the water while connected to a main power supply.
- Never touch the product or cables with wet hands.
- Ensure the product is not connected to a power supply when not in use.
Environmental Note:
To save the environment and reduce unnecessary paper, the manual is available in various languages online at www.PartyFunLights.com/Manuals.
Need help?
General
To Next Page