EasyManua.ls Logo

Pattfield Ergo Tools E-KS 2035 - User Manual

Pattfield Ergo Tools E-KS 2035
96 pages
Go to English
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
k
Originalbetriebsanleitung
Elektrokettensäge
t
Original operating instructions
Electric chainsaw
p
Mode d’emploi d’origine
Scie à chaîne électrique
C
Istruzioni per l’uso originali
Motosega elettrica
N
Originele handleiding
Elektrische kettingzaag
U
Original-bruksanvisning
Elektrisk kedjesåg
j
Originální návod k obsluze
Elektrická řetězová pila
W
Originálny návod na obsluhu
Elektrická reťazová píla
Q
Instrucţiuni de utilizare originale
Ferăstrăul electric cu lanţ
Art.-Nr.: 45.002.12 I.-Nr.: 01029
E-KS 2035
Anleitung_E-KS_2035_SPK7:_ 06.07.2009 13:36 Uhr Seite 1

Table of Contents

Questions and Answers

  • R
    rodney05Aug 12, 2025
    Why Pattfield Ergo Tools Chainsaw won't start?
    • T
      Thomas DavisAug 12, 2025
      Your Pattfield Ergo Tools Chainsaw might not start due to several reasons: the quick stop brake may be triggered (pull the hand protection back to the normal position), there could be no power supply (check the power supply), the mains outlet might be defective (try an alternative source of electrical power, replace if necessary), the power extension cable could be damaged (check the cable and replace as required), or the fuse might be defective (replace the fuse).
  • N
    Nicole HigginsAug 19, 2025
    What to do if Pattfield Ergo Tools E-KS 2035 Chainsaw chain/guide rail gets hot?
    • Z
      Zachary HamptonAug 19, 2025
      If the chain/guide rail of your Pattfield Ergo Tools Chainsaw is getting hot, it could be due to several reasons: there might be no oil in the tank (fill up with oil), the oil tank cap breather could be blocked (clean the oil tank cap), the oil outlet might be blocked (clear the oil outlet), or the chain could be blunt (re-sharpen or replace the chain).
  • A
    amy42Aug 27, 2025
    How to fix Pattfield Ergo Tools E-KS 2035 Chainsaw that is vibrating too much?
    • A
      Amy SchaeferAug 27, 2025
      If your Pattfield Ergo Tools Chainsaw is juddering, vibrating, or not sawing properly, consider the following: * The chain tension might be too loose (adjust the chain tension). * The chain could be blunt (re-sharpen or replace the chain). * The chain might be worn (replace the chain). * The saw teeth could be pointing in the wrong direction (reinstall the saw chain with the teeth facing in the correct direction).
  • R
    Ryan CookSep 3, 2025
    What to do if Pattfield Ergo Tools E-KS 2035 saw chain is dry?
    • R
      Randall MillerSep 3, 2025
      If the saw chain of your Pattfield Ergo Tools Chainsaw is dry, it could be caused by: no oil in the tank (fill up with oil), the oil tank cap breather being blocked (clean the oil tank cap), or the oil outlet being blocked (clear the oil outlet).

Pattfield Ergo Tools E-KS 2035 Specifications

General IconGeneral
Power SourceElectric
Power2000 W
Bar Length35 cm
Chain Speed13.5 m/s
Voltage230 V
Frequency50 Hz
Chain Pitch3/8"
Chain Gauge1.3 mm
Oil Tank Capacity0.15 L