- 14 -
the two levers downwards and then push
the footrest downwards (fig_a); to raise the
footrest lift it upwards (fig_b).
11 FRONT BAR: To pull the front bar out by one
position, press the button as shown and pull
outwards (fig_a). To remove the front bar,
pull it out to the second position and remove
(fig_b). Open-close front bar: pull out on one
side and rotate.
12 HOOD: The hood comes with a loop for
hanging your child's favorite toy (fig_a) and a
see-through window for observing your child
(fig_b), which can be lifted and fastened. You
can detach the Velcro, roll up the back of the
hood and fasten it at the top with the rubber
band to allow greater ventilation during use
with the backrest down (fig_c). The hood may
be pulled forward into several positions (fig_d).
13 ADJUSTING THE BACKREST: to lower the
backrest, press the clip and the backrest will
move down to the desired position.
To raise the backrest, press the clip and lift
the backrest to the desired height.
14 FIVE POINT SAFETY HARNESS: To fasten it,
push the two waist strap buckles (with the
shoulder straps attached – arrow_a) into
the leg divider until they click into place
(arrow_b). To unfasten it, press the round
button in the centre of the buckle (arrow_c)
and pull the waist straps out (arrow_d).
15 To tighten the waist strap, pull on both sides
in the direction of the arrow (arrow_a). To
loosen it, move it in the opposite direction.
16 Before adjusting the height of the safety
harness remove the shoulder pads (fig_a). To
adjust the height, slip the belts through the
eyelet in the fabric (fig_b) and position them
in the most suitable eyelet.
17 FOLDING UP: To fold up the stroller, you must
ensure the front wheel swivels and the hood
are closed, when fastened. Place the handle
as shown in the figure (fig_a). Pull the inside
handle on the base (fig_b) and lift it (fig_c);
the handle will drop forward until the frame
is closed.
18 To close correctly, check the side hook is
inserted (fig_a). If not automatically locked,
compress the chassis slightly. When folded,
the stroller will free standing (fig_b).
19 For greater compactness, it is possible to
remove the wheels.
To remove the rear wheels: pull the pivot
outwards and remove the wheel as shown in
the figure (fig_a).
To remove the front wheels: press the tab as
shown, and remove the wheel (fig_b).
TRANSPORT: the stroller can be carried
comfortably locking the front wheels and
grasping the main handle (fig_c).
20 REMOVABLE ITEMS: to remove the hood, take
the elastic off from the buttons on the inside
of the handlebar (fig_a), detach the press
studs the sides of the chassis (fig_b), detach
the Velcro strip from the backrest (fig_c) and
remove the attachments of the hood from
their positions on the chassis (fig_d).
21 To remove the seat fabric, press in the
holes on the inside of the chassis (fig_a);
remove, from the side of the seat, the rigid
flap of the chassis fabric ((fig_b), unfasten
the elastic of the net from the side buttons
inside the handlebar (fig_c) and unfasten
the elastics from the buttons inside the
chassis (fig_d).
22 From the front, remove the lining from the
foot platform (fig_a), remove the leg divider
strap from under the seat (fig_b), unbutton
the seat fabric (fig_c), unscrew the waist belt
on the side (fig_d) and remove the seat fabric
from the backrest (fig_e).
GANCIOMATIC SYSTEM
The Ganciomatic System is the quick,
practical system that allows you to fasten the
Primo Viaggio 4•35 car seat (sold separately)
onto the stroller using the Ganciomatic
hooks.
23 GANCIOMATIC HOOKS ON THE STROLLER: to
lift the stroller's Ganciomatic hooks, pull back
the fabric at the corners of the seat.
Pull the frame's side levers outwards (fig_a)
and turn the Ganciomatic hooks upwards.
_ To lower the hooks, proceed in the opposite
order.
GANCIOMATIC FASTENING
24 Book Cross + Primo Viaggio 4•35
To mount the car seat on the stroller or
chassis, you must:
_ Engage the stroller's brake;
_ Lift the stroller's Ganciomatic hooks;
_ Pull the front bar out to the second position
(fig_a).
_ Fully lower the backrest, if in place.
_ Place the car seat, facing mom, on the
Ganciomatic hooks and push it down until it
clicks into place.
_ Once the seat is mounted, lift the backrest - if
in place - to the maximum height (fig_b).
_ See the instruction manual to release the car
seat from the stroller.
SERIAL NUMBERS
25 Information about the production date can
be found on the Book Cross .
_ The product name, production date and serial
number of the chassis.
This information is required for any
complaints.
To Next Page
Loading...
