- 14 -
ensure it engages securely onto the base.
2 FITTING THE WHEELS: Slot the uprights into the
rear wheel crosspiece (fig_a), ensuring that it is
facing the right way, then push the rear wheels on
and make sure that they click into place (fig_b).
3 FITTING THE BASKET: if lowered, lift the basket
tube to the horizontal position. Press the silver
buttons under the metal basket tube located at
the back of the stroller (fig_a) and remove the
metal tube (fig_b). Thread the tube through the
fabric loop on the back of the basket, making sure
that the two silver buttons are facing downward
(fig_c). Re-attach the tube to the housings (fig_d).
4 Secure the two upper basket vinyl eyelets to
the two grey buttons on either side of the metal
tube housing. Please note that the eyelets open
(fig_e). Remove the cardboard from the lower
rear bar. IMPORTANT! Secure the two lower
basket vinyl eyelets to the two grey buttons
on the top of the lower rear bar. Please note
that the eyelets open (fig_f). WARNING! If this
operation is not performed correctly, the basket
will not properly hold the weight.
Attach the basket tabs to the grey buttons on
the front of the frame (figure).
REFER TO OUR INSTALLATION INSTRUCTIONS
VIDEO AT: WWW.PEGPEREGO.COM
5 FIXED OR SWIVELING FRONT WHEELS: Lift the
levers to prevent the wheels from swiveling
(fig_a) and lower them to allow the wheels to
swivel (fig_b). On uneven surfaces, the wheels
should be set to their fixed position.
6 BRAKE: Press the lever down to apply the brake
on the chassis and lift it to release the brake.
7 ADJUSTABLE HANDLEBAR: To adjust the height
of the handlebar, press both of the side buttons
at the same time (fig_a) and swing it into the
desired position (fig_b), then release the buttons.
8 ATTACHING THE SEAT ONTO THE CHASSIS:
the reversible seat can be attached onto the
chassis to face mum or to face outwards (fig_a).
Position centrally on the chassis and press down
with both hands until it double clicks into place.
To make sure that it is properly attached, take
hold of the seat via the front bar and pull it up.
9 REMOVING THE SEAT FROM THE CHASSIS: Hold
down the two round buttons on the sides of
the seat (fig_a), press the two levers under the
armrests (fig_b) and pull up the seat (fig_c) until
it is released. The seat can be removed from and
re-attached to the chassis when there is a child in it.
10 FRONT BAR: Before attaching the front bar,
press the buttons on the sides of the armrests
and remove the caps (fig_a). To attach the front
bar, guide the connections into the armrests
and push towards the seat until they click into
place (fig_b). To remove the front bar, press
the two buttons and pull it out (fig_c). To make
it easier for the child to get in and out, it is
possible to open the front bar on one side only.
If you wish to use the stroller without the front
bar, put the caps back in the armrests.
11 BACKREST: to recline the backrest lift the lever
(fig_a) and choose one of the 4 positions (fig_b).
12 FOOTREST: to lower the footrest push the two
levers downwards and then push the footrest
downwards (fig_a); to raise the footrest lift it
upwards (fig_b).
13 FIVE POINT SAFETY HARNESS: To fasten it,
push the two waist strap buckles (with the
shoulder straps attached – arrow_a) into
the leg divider until they click into place
(arrow_b). To unfasten it, press the round
button in the centre of the buckle (arrow_c)
and pull the waist straps out (arrow_d).
14 To tighten the waist strap, pull on both sides
in the direction of the arrow (arrow_a). To
loosen it, move it in the opposite direction.
15 To adjust the height of the safety harnesses,
release the two buckles on the rear of the
backrest.
Pull the shoulder straps towards you (arrow_a)
until the buckles are released and insert them
in the backrest loops (arrow_b). Remove the
shoulder straps from the sack (arrow_c) and
insert them in the most appropriate loop
(arrow_d), then re-attach the two buckles on the
rear of the backrest (arrow_e) The buckles are
securely attached when a click is heard (fig_f).
16 HOOD: WARNING. Ensure the buttons are
fastened on the rear of the backrest. If this
is not the case, fasten them now (fig_a). To
open the hood, pull it towards you; to close
the hood, push it backwards. The hood may
only be used as a parasol if the backrest
is not fully reclined. In this case, open the
double slider zipper (fig_b) and unfasten the
hood buttons on the rear of the backrest.
The hood comes with a loop from which to
dangle baby’s favorite toy (fig_c).
17 COVER: put on the cover, and fasten it
underneath (fig_a) and on the sides of the
footboard. For the baby carriage version, move
the footboard up and place the cover over the
front bar (fig_b), fastening it to the buttons of
the hood (fig_c). For the stroller version, move
the footboard down, insert the cover underneath
the front bar (fig_d) and fix it in place.
18 BABY SAFE: pull the Baby Safe system out from
under the leg rest (fig_a), attach it to the seat
(fig_b), fit the front bar (fig_c), unbutton the fabric
covering at the side and then attach the Baby Safe
system to the sides of the armrests (fig_d). A fitted
Baby Safe system is shown in Figure E.
19 RAIN CANOPY: position the rain canopy on
the stroller (fig_a) and insert the two lateral
loops over the hood buttons (fig_b).
20 Secure the rain canopy by attaching the
elastic loop to the rear uprights (fig_a) or to
the front uprights (fig_b), according to the
seat position.
21 FOLDING UP: to fold up the seat press the
To Next Page
Loading...
