• IMPORTANT: read these instructions
carefully and keep them for future
reference.
Failure to follow these instructions could
put the childʼs safety at risk.
• PEG PEREGO reserves the right to make any
necessary changes or improvements to the
products shown at any time without notice.
CUSTOMER SERVICE
If parts of the model are accidentally lost or
damaged, use only original Peg Perego spare
parts. Contact the Peg Perego Customer
Service for all repair work, replacements,
information about products, and sale of
original spare parts and accessories, at the
following:
CANADA:
tel.: 905.839.3371
fax: 905.839.9542
Call us toll free: 1.800.661.5050
www.pegperego.com
INSTRUCTIONS FOR USE
OPENING
1•
Before opening the stroller remove the two
protective caps from the hooks as shown in
the figure. Otherwise, the stroller will not
open correctly.
2• To open the stroller, pull up the two
levers on the handles and
3• at the same time, lift the stroller, which
will open automatically. To make sure
that the stroller has been set up correctly,
check the two side hooks (see figure).
ASSEMBLYING THE STROLLER
4• To mount the front wheels, lower Lever
A and slip the wheels onto the axle,
as shown in the figure. Press until the
wheels click into place.
5• To assemble the rear wheels fasten the
wheels connected by the break wire, as
indicated in the figure.
6• Carefully distinguish the left wheel from
the right, to fasten the two rear wheels
properly. The left wheel has a rib on the
wheel tube and one on the chassis to
guarantee proper fastening (see figure).
7• Make sure that it is fastened properly, as
indicated in the figure (click).
8• To mount the basket, slide the slots onto
the front hooks A and the rear hooks B
and C.
9• The figure shows the mounted basket.
10• The drink-holder can be attached to the
EN•ENGLISH
left or the right handle of the stroller,
using the two bands.
• To mount the drink-holder to the handle,
widen the clamp and fasten as shown in
the figure.
11• Slide the clamp in the drink-holder until
it clicks.
Do not put hot drinks in the drink-holder,
nor items weighing more than 1 kg (2.2
lbs).
FRONT BAR
12•
The stroller comes with caps on the
armrests. To attach the front bar, remove
the caps first. (Keep the caps, in case you
want to use the stroller without the front
bar). To remove the caps, press the buttons
under the armrests while pulling the caps
off.
13•
To mount the front bar, press the buttons
while slipping the front bar onto the
armrests, as shown in the figure. Push until
the armrest clicks into place. The armrest
will now be in the second position (2).
14• To place the front bar in the first position
(1), press the buttons under the armrests
while pushing the front bar towards the
stroller.
15• To remove the front bar, press the two
buttons under the armrests while pulling
the front bar out. (The front bar will
click into the second position). Press the
buttons again, and pull the front bar off
the stroller. The front bar can be opened
on one side only to allow the child to
get in and out of the stroller more easily
when he is older.
BRAKE
16• To apply the brakes, push down with
one foot the bars on the rear wheels,
as shown in the figure. To release the
brakes, draw the bar up. Always set the
brakes on the stroller when it is not in
motion.
SAFETY BELT
17• A: Make sure that the brace is properly
inserted by pushing as shown in the
figure. B: Fasten the belt as shown in the
figure.
18• To unfasten the belt, press on the buckle
sides and pull out the waist strap.
19• The new safety belt is now easier to
fasten thanks to the "snap-open-and-
shut" device. Before fastening the safety
belt, attach the buckle to the backrest
by inserting the tab through the special
holder, as shown in the figure. After
fastening the safety belt on your child,
detach it from the backrest to allow the
child more freedom of movement. The
buckle must remain below the child's
shoulders.
To Next Page
Loading...
