Pepperl+Fuchs INX360D-F99-I2E2-V15

To Next Page

Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany

Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com

Inclination sensor INX360D-F99-I2E2-V15

Release date: 2011-08-17 14:11 Date of edition: 2011-08-17 201503_eng.xml

Model number

INX360D-F99-I2E2-V15

Features

• Measuring range 0 ... 360°

• Analog output 4 mA ... 20 mA

• Evaluation limits can be taught-in

• 2 programmable switch outputs

• High shock resistance

• e1-Type approval

• Increased noise immunity 100 V/m

EMC Properties

Emitted interference and interference immunity in accordance with motor vehicle directive 2006/28/EG (e1 Type approval)

Interference immunity in accordance with

DIN ISO 11452-2: 100 V/m

Frequency band 20 MHz up to 2 GHz

Mains-borne interference in accordance with ISO 7637-2:

Technical Data

General specifications

Type Inclination sensor, 1-axis

Measurement range 0 ... 360 °

Absolute accuracy ≤ ± 0.5 °

Response delay ≤ 20 ms

Resolution ≤ 0.1 °

Repeat accuracy ≤ ± 0.1 °

Temperature influence ≤ 0.027 °/K

Functional safety related parameters

MTTF

300 a

Mission Time (T

) 20 a

Diagnostic Coverage (DC) 0 %

Indicators/operating means

Operating display LED, green

TEACH-IN indication 2 LEDs yellow (switching status), flashing

Button 2 push-buttons ( Switch points programming , Evaluation

range programming )

Switching state 2 yellow LEDs: Switching status (each output)

Electrical specifications

Operating voltage U

10 ... 30 V DC

No-load supply current I

≤ 25 mA

Time delay before availability t

≤ 200 ms

Switching output

Output type 2 switch outputs PNP, NO , reverse polarity protected ,

short-circuit protected

Operating current I

≤ 100 mA

Voltage drop ≤ 3 V

Analog output

Output type 1 current output 4 ... 20 mA

Load resistor 0 ... 200 Ω at U

= 10 ... 18 V

0 ... 500 Ω at U

= 18 ... 30 V

Ambient conditions

Ambient temperature -40 ... 85 °C (-40 ... 185 °F)

Storage temperature -40 ... 85 °C (-40 ... 185 °F)

Mechanical specifications

Connection type M12 x 1 connector, 5-pin

Housing material PA

Protection degree IP68 / IP69K

Mass 240 g

Compliance with standards and

directives

Standard conformity

Shock and impact resistance 100 g according to DIN EN 60068-2-27

Standards EN 60947-5-2:2007

IEC 60947-5-2:2007

Approvals and certificates

CSA approval cCSAus Listed, General Purpose, Class 2 Power Source

CCC approval Products with a maximum operating voltage of ≤36 V do

not bear a CCC marking because they do not require

approval.

e1 Type approval 2006/28/EG

Pulse 1 2a 2b 3a 3b 4

Severity level III III III III III III

Failure criterion C A C A A C

EN 61000-4-2: CD: 8 kV / AD: 15 kV

Severity level IV IV

EN 61000-4-3: 30 V/m (80...2500 MHz)

Severity level IV

EN 61000-4-4: 2 kV

Severity level III

EN 61000-4-6: 10 V (0.01...80 MHz)

Severity level III

EN 55011: Klasse A

Need help?

Do you have a question about the Pepperl+Fuchs INX360D-F99-I2E2-V15 and is the answer not in the manual?

The Pepperl+Fuchs INX360D-F99-12E2-V15 is a 1-axis inclination sensor designed for robust and precise angle measurement in industrial and automotive applications. It offers a wide measurement range, high accuracy, and programmable switching outputs, making it versatile for various control and monitoring tasks.

Function Description:

The sensor measures inclination over a full 360° range. It provides both an analog current output (4 mA to 20 mA) and two programmable PNP switching outputs. The switching outputs can be configured to activate at specific inclination angles, which can be taught-in by the user. This allows for flexible control based on the detected angle. The analog output provides a continuous signal proportional to the inclination, enabling precise monitoring. The device features a TEACH-IN function for easy setup of switching points and evaluation limits, eliminating the need for complex programming. Its robust design, including a cast aluminum housing and high protection degree, ensures reliable operation in harsh environments.

Important Technical Specifications:

Type: Inclination sensor, 1-axis
Measurement Range: 0...360°
Absolute Accuracy: ≤ ± 0.5°
Resolution: ≤ 0.1°
Repeat Accuracy: ≤ ± 0.1°
Temperature Influence: ≤ 0.027 °/K
Response Delay: < 20 ms
Operating Voltage (UB): 10...30 V DC
No-load Supply Current (I0): ≤ 25 mA
Switching Outputs: 2 x PNP, NO, reverse polarity protected, short-circuit protected, ≤ 100 mA operating current, ≤ 3 V voltage drop.
Analog Output: 1 x current output 4...20 mA. Load resistor: 0...200 Ω at UB = 10...18 V; 0...500 Ω at UB = 18...30 V.
Ambient Temperature: -40...85 °C (-40...185 °F)
Storage Temperature: -40...85 °C (-40...185 °F)
Connection Type: M12 x 1 connector, 5-pin
Housing Material: PA (Polyamide)
Protection Degree: IP68/IP69K
Mass: 240 g
Functional Safety (MTTFd): 300 years, Mission Time (TM): 20 years, Diagnostic Coverage (DC): 0%
Shock and Impact Resistance: 100 g according to DIN EN 60068-2-27
EMC Properties: Compliant with motor vehicle directive 2006/28/EG (e1 Type approval), DIN ISO 11452-2 (100 V/m), ISO 7637-2, EN 61000-4-2, EN 61000-4-3, EN 61000-4-4, EN 61000-4-6, EN 55011 (Klasse A).
Approvals: CCSAus Listed, General Purpose, Class 2 Power Source; CCC approval (for products ≤36V); e1 Type approval (2006/28/EG).

Usage Features:

Easy Configuration: The sensor features two push-buttons for TEACH-IN programming of switching points and evaluation ranges. This simplifies setup and calibration in the field.
Visual Indicators: A green LED indicates normal operation, while two yellow LEDs provide feedback on switching status and TEACH-IN processes. Flashing patterns communicate different states, such as successful TEACH-IN or error conditions.
Flexible Mounting: The sensor module is housed within a cast aluminum enclosure. It can be mounted on a flat surface with minimum dimensions of 70 mm x 50 mm using four countersunk screws. The sensor's zero position is typically with the electrical connection facing straight upwards, but custom orientations can be preset at the factory. The modular design allows the sensor module to be easily removed from its housing for mounting the housing first, then reinserting the module.
High Noise Immunity: With increased noise immunity of 100 V/m, the sensor is well-suited for electrically noisy industrial environments.
e1 Type Approval: This certification makes the sensor suitable for use in motor vehicle applications, ensuring compliance with relevant automotive EMC standards.
Programmable Switching Outputs: Two independent switching outputs can be programmed to trigger at specific inclination angles, providing flexible control options for various applications like tilt monitoring, leveling, or position detection.
Analog Output for Continuous Monitoring: The 4-20 mA current output offers a continuous and proportional signal of the inclination, allowing for precise analog control or data logging.
Robust Design: The IP68/IP69K protection degree ensures resistance against dust, water jets, and even temporary submersion, making it suitable for demanding outdoor or wash-down applications. The PA housing material further contributes to its durability.

Maintenance Features:

Self-Diagnosis: The device includes indicators for various states, including power, switching status, and TEACH-IN processes, which can aid in troubleshooting.
Factory Reset: The sensor can be reset to its factory settings by pressing and holding both buttons for more than 10 seconds, simplifying recovery from misconfigurations.
Under-voltage Indication: If the supply voltage falls below a critical value (e.g., 7 V), the green LED and yellow LEDs will deactivate, and the green "power" LED will flash rapidly, indicating a power supply issue. This provides an early warning for potential operational problems.
Modular Construction: The sensor module can be removed from its housing, which might simplify replacement or inspection if needed, although the manual primarily describes this for initial mounting.
No Specific Routine Maintenance: The technical data and description do not indicate any specific routine maintenance requirements for the sensor itself, suggesting a low-maintenance design. Its robust construction and high protection degree are designed for long-term reliability without frequent intervention.