Perel EVM831 User Manual

28.04.2010
Volta
g
e mea
s
Do n
o
Alway
s
rms.
K
meas
u
to a ci
• Connect th
e
VmA jack
• For DC volt
a
the ran
g
e i
s
appropriate
• For AC volt
a
the ran
g
e i
s
appropriate
• Connect th
e
• The measu
r
Notes:
• For D
C
test le
• When
althou
norm
a
stabili
z
Direct curren
Do no
t
This
d
not s
u
Curre
n
to 10
A
contin
meas
u
Alway
s
rms.
K
meas
u
• For measu
j
ack and th
e
500mA/250
• For measu
and the bla
c
10A/220V).
• For DC mea
desired ran
g
• For DC mea
desired ran
g
• When the r
a
to the appr
o
• Connect th
e
• Read the m
e
s
urements
o
t measure circuits
w
s
be careful when wo
r
K
eep your fin
g
ers beh
i
u
rement. Do not touc
h
rcuit which is bein
g
t
e
e
black test lead to th
e
.
ag
es, set the selector
s
unknown, always se
t
ran
g
e.
ag
es, set the selector
s
unknown, always se
t
ran
g
e.
e
test probes with the
r
ed volta
g
e is shown
o
C
-measurements: wh
e
ad, the indicated val
u
the mV ran
g
e is sele
c
g
h the probes are no
t
a
l and is caused by th
e
z
e and
g
ive a proper
m
t measurements
t
measure current in
c
d
evice is only desi
gn
u
itable for alternati
n
t measurements V
m
A
use the 10A
j
ack. W
uous measurement f
o
u
rements.
s
be careful when wo
r
K
eep your fin
g
ers beh
u
rement.
rements up to 200
m
e
black lead to the C
O
V).
rements up to 10A:
c
k lead to the COM
j
a
surements up to 200
m
g
e.
surements up to 10A
,
g
e (use the 10A
j
ack
)
a
n
g
e is unknown, alw
a
o
priate ran
g
e.
e
test probes in series
e
asured cuurent from
EVM831
8
w
here volta
g
es > 5
r
kin
g
with volta
g
es a
b
i
nd the probe barrier
s
h
unused terminals w
h
e
sted.
e
COM
j
ack and the r
e
switch to V in the
d
t
the hi
g
hest possible
switch to V in the
t
the hi
g
hest possible
circuit under test.
o
n the display.
e
n a ne
g
ative polarity
u
e is preceded by a “-
c
ted, the display may
t
connected to a devi
c
e
hi
g
h input sensitivit
y
m
easurement when c
o
c
ircuits with volta
g
es
n
ed for DC current
m
n
g
current measur
e
m
A
j
ack max. 200m
A
hen measurin
g
curre
n
o
llowed by a 15 minu
t
r
kin
g
with volta
g
es a
b
ind the probe barrier
s
m
A: connect the red t
O
M
j
ack (protected wi
t
connect the red test
ck (protected with a
c
m
A, set the selector s
,
set the selector swit
c
)
.
a
ys set the hi
g
hest p
o
with the circuit.
the display.
©Velleman n
v
00V CAT II
b
ove 60Vdc or 30Vac
s
at all times during
h
en the meter is link
e
e
d test lead to the
d
esired ran
g
e. When
ran
g
e and lower to t
h
desired ran
g
e. When
ran
g
e and lower to t
h
is present at the red
” si
g
n.
show a varyin
g
readi
n
c
e or circuit. This is
y
. The reading will
o
nnected to a circuit.
> 250V
m
easurements; it i
s
e
ments.
A
; for measurements
u
n
ts up to 10A, max. 1
t
es break between 2
b
ove 60Vdc or 30Vac
s
at all times durin
g
est lead to the Vm
A
t
h a ceramic fuse
lead to the 10A
j
ack
c
eramic fuse
witch to A in the
c
h to A in the
o
ssible ran
g
e and low
e
v
e
d
h
e
h
e
ng
s
u
p
0s
A
e
r

Perel EVM831 Specifications

General

Brand	Perel
Model	EVM831
Category	Multimeter
Language	English