Perel EVM831 User Manual

28.04.2010
Notes:
• For DC-c
u
red test l
• The µA a
F500mA
/
fuse.
Resistance
m
Do n
o
• Connect th
e
jack.
• Set the sel
e
unknown, a
appropriate
• Connect th
e
• The measu
r
Notes:
• Never pe
capacito
r
• To incre
a
tips of th
the test l
• For resis
t
to stabili
z
• Should t
h
open cir
c
Continuity te
s
Do n
o
• Connect th
e
VmA
j
ack
• Set the sel
e
• Connect th
e
• When the
m
produced a
n
resistance
e
will show “1
Note:
• Never pe
capacito
r
Diode test
Do n
o
• Connect th
e
VmA
j
ack
• Set the sel
e
• Connect th
e
the anode,
b
u
rrent measurement
s
ead, the indicated va
l
nd mA-ranges are pr
o
/
250V fuse; the 10A r
a
m
easurements
o
t perform resistan
c
e
red test lead to the
V
e
ction switch to the d
e
lways select the hi
g
h
e
ran
g
e.
e
test probes to the ci
r
r
ed value appears on
t
rform resistance mea
r
s are completely disc
h
a
se accuracy when m
e
e measurin
g
probes t
eads. Subtract this v
a
t
ance measurements
a
z
e the read-out.
h
e measured resistan
c
c
uit, the display will s
h
s
t
o
t perform continui
t
e
black test lead to th
e
.
e
ction switch to 200
e
test leads to the circ
m
easured resistance i
s
n
d the resistance is s
h
e
xceed the selected r
a
”.
rform continuity mea
s
r
s are completely disc
h
o
t perform diode m
e
e
black test lead to th
e
.
e
ction switch to 2000
e
test leads to the circ
b
lack test probe to th
e
EVM831
9
s
, when a ne
g
ative po
l
l
ue is preceded by a “
o
tected a
g
ainst ove
r
-
c
a
n
g
e is protected wit
h
c
e measurements o
n
V
mA
j
ack and the b
e
sired "Ω” range. Whe
e
st possible ran
g
e an
d
r
cuit/component und
e
t
he display.
surements on a live
c
h
ar
g
ed.
e
asurin
g
low resistan
c
o
g
ether to determine
a
lue from the measur
e
a
bove 1M the mete
r
c
e exceed the selecte
d
h
ow “1”.
t
y measurements o
n
e
COM
j
ack and the r
e
.
uit/component under
s
less than 50 a con
t
h
owed on the display.
a
n
g
e or in case of an
o
s
urements on a live c
h
ar
g
ed.
e
asurements on liv
e
e
COM
j
ack and the r
e
.
uit/component under
e
cathode).
©Velleman n
v
l
arity is present at th
e
-” sign.
c
urrent with a cerami
c
h
a ceramic F10A/250
n
live circuits.
lack lead to the "CO
M
n the ran
g
e is
d
lower to the
e
r test.
c
ircuit and make sure
c
e values, first hold th
the resistance value
e
d value of the circui
t
r
needs a few second
s
d
ran
g
e or in case of
a
n
live circuits.
e
d test lead to the
test.
t
inuous beep is
Should the measure
d
o
pen circuit, the displ
a
ircuit and make sure
a
e
circuits.
e
d test lead to the
test (red test probe
t
v
e
c
V
M
"
all
e
of
t
.
s
a
n
d
a
y
a
ll
t
o

Perel EVM831 Specifications

General

Brand	Perel
Model	EVM831
Category	Multimeter
Language	English