Performance Tool W41023 - User Manual

WARNING
It is the owner and/or operators’ responsibility to study all WARNINGS, operating, and maintenance
instructions contained on the product label and instruction manual prior to operation of this product. The
owner/operator shall retain product instructions for future reference.
The owner and/or operator are responsible for maintenance, maintaining all decals or warning labels and
while in use, maintaining the unit in good working order. If the owner and/or operator are not fluent in English,
the product warnings and instructions shall be read and discussed with the operators’ native language by the
purchaser/owner or his designee. Make sure that the operator comprehends its contents. Safety information
shall be emphasized and understood prior to usage. The product shall be inspected per the operating
instructions.
Users of this product must fully understand these instructions. Each person operating this product must also
be of sound mind and body and must not be under the influence of any substance that might impair their
vision, dexterity, or judgment.
Protect yourself and others by observing all safety information.
Failure to comply with instructions could result in personal injury and/or property damage!
If you encounter any problems or difficulties, please contact our customer service department at:
1-800-426-1262 between 6:30 a.m. and 4:30 p.m. Pacific time.
6 TON
JACK STANDS
OWNER’S MANUAL
Item Number W41023

Summary

Safety Guidelines and Definitions

Signal Words Explanation

Explains DANGER, WARNING, CAUTION, NOTICE signal words used in the manual.

Unpacking and Inspection

Handling Damaged Products

Instructions for handling products damaged during shipment or misuse, emphasizing repair before operation.

Specifications

Important Safety Information

General Warnings

Critical warnings regarding reading instructions, overload, and load positioning for safe operation.

Operation Safety Precautions

Safety precautions to ensure personnel are clear of the load during lowering and not underneath.

Operation

Jacking and Positioning

Guidance on vehicle jacking procedures and correct stand positioning based on manufacturer specifications.

Adjusting and Lowering Load

Instructions on how to adjust the jack stand height and safely lower the load onto the stands.

Maintenance and Inspection

Pre-Use Checks and Modifications

Visual inspection before use and prohibition of product modifications due to potential hazards.

1 Year Limited Warranty

Overview

1. Function Description
2. Important Technical Specifications
3. Usage Features
4. Maintenance Features
5. Warranty Information

This document is the owner's manual for 6-ton jack stands, identified by Item Number W41023. It provides essential information for safe operation, maintenance, and specifications of the product.

Function Description

The 6-ton jack stands are designed to provide stable support for vehicles after they have been lifted by a jack. They are intended for use in pairs on hard, level surfaces capable of sustaining the load. The primary function is to securely hold a lifted load, allowing for maintenance or repair work underneath the vehicle. The stands feature an adjustable saddle shaft with a control lever and pawl mechanism to lock the shaft at the desired height, ensuring the load is fully engaged into the teeth for stability.

Important Technical Specifications

• Capacity: 12,000 lbs.
• Minimum Lift Height: 15 1/2 in.
• Maximum Lift Height: 23 3/4 in.
• Base Length: 9 5/8 in.
• Base Width: 10 15/16 in.

These specifications are subject to change without notice.

Usage Features

The manual emphasizes several critical usage features and safety guidelines:

• Pre-Operation Check: Before operation, users must read and understand the entire instruction manual, including all warnings, operating, and maintenance instructions. The owner/operator is responsible for maintaining the unit in good working order and ensuring all decals or warning labels are intact. If the owner/operator is not fluent in English, the product warnings and instructions must be read and discussed in their native language by the purchaser/owner or their designee to ensure comprehension.
• Safe Positioning: Jack stands must always be used in pairs on a hard, level surface capable of sustaining the load. Using them on uneven or soft surfaces can lead to instability and potential loss of the load. The load must be positioned on the center of the saddle only.
• Vehicle Jacking: Users should refer to their vehicle owner's manual for proper jacking procedures and identify the specified load support points.
• Adjusting Height: To adjust the stands, the control lever should be held up while lifting the saddle shaft to the desired height. Once the height is set, the control lever must be pushed down to lock the pawl into the teeth of the center column. It is crucial to ensure the pawl is fully engaged into the teeth for secure support.
• Lowering Load: After the stands are properly positioned and adjusted, the load should be carefully lowered onto them. All personnel must be clear of the load before it is lowered. No one should pass underneath the load until it is securely supported by the jack stands.
• Overload Prevention: Do not overload the jack stands beyond their rated capacity (12,000 lbs.), as this can cause damage or failure of the stands.
• Prohibited Modifications: No modifications should be made to the product due to the potential hazards associated with the misuse of this type of equipment.

Maintenance Features

Regular maintenance and inspection are crucial for the safe and reliable operation of the jack stands:

• Visual Inspection: A visual inspection must be performed before each use. This inspection should check for cracks, cracked welds, and any missing or damaged parts.
• Damage Protocol: Any stand that appears to be damaged in any way must be immediately removed from service. All damaged parts must be repaired or replaced as needed before the product is operated again.
• Secure Components: Before putting the product into service, ensure that all nuts, bolts, and fittings are secure.
• Customer Service: If any problems or difficulties are encountered, or if parts are missing or damaged, customers should contact the customer service department at 1-800-426-1262 between 6:30 a.m. and 4:30 p.m. Pacific time. When calling, the serial number, model number, and date of purchase should be available for reference.

Warranty Information

The product comes with a 1-year limited warranty from PERFORMANCE TOOL®. This warranty extends only to original retail purchasers and covers defects in materials and workmanship under normal use and service. A defective product can be returned for a free replacement within 90 days of purchase. After 90 days and up to one year, PERFORMANCE TOOL® will replace defective parts at no charge, provided a sales receipt showing the date of purchase accompanies the defective product or part. The warranty excludes consumables (blades, bits, fuses, hoses, etc.) and does not cover products used for purposes other than their design, repaired or altered in any way, or subjected to misuse, neglect, accident, or normal wear and tear. PERFORMANCE TOOL® does not authorize any other person to make warranties or assume liability on its behalf. The warranty explicitly disclaims express or implied warranties of merchantability and fitness for a particular purpose, except for goods purchased for personal, family, or household use, where an implied warranty of merchantability (and, if applicable, fitness for a particular purpose) is provided for the particular qualities or characteristics and duration expressly warranted. The company is not liable for consequential, incidental, or special damages. The sole remedy for a defective product or part is repair or replacement.

Performance Tool W41023 Specifications