Performance Tool W41022

Need help?

Do you have a question about the Performance Tool W41022 and is the answer not in the manual?

Summary

Safety Guidelines and Information

Hazard Definitions

Defines DANGER, WARNING, CAUTION, NOTICE for hazard emphasis.

Operational Safety Warnings

Read, understand, follow instructions. Do not overload, position centrally, use on level surfaces.

Personnel Safety

Ensure personnel are clear of load before lowering. Avoid passing under supported load.

Unpacking, Inspection, and Operation

Unpacking and Inspection

Inspect for damage, check parts. Contact customer service for issues.

Operation Procedure

Refer to vehicle manual, lift on specified points, adjust height by locking pawl.

Maintenance and Modifications

Visual inspection for damage before use. No product modifications allowed.

Limited Warranty

Warranty Terms and Exclusions

Free from defects, 90 day replacement, up to 1 year for parts. Excludes misuse, accident, alterations.

Liability Limitations

Limits liability for consequential, incidental, or special damages.

This document is an owner's manual for 3-ton jack stands, specifically item number W41022, manufactured by Performance Tool. It provides essential information for the safe and effective operation, maintenance, and understanding of the product.

Function Description

The 3-ton jack stands are designed to securely support a lifted vehicle or load, allowing for maintenance or repair work underneath. They are intended to be used in pairs on a hard, level surface capable of sustaining the load. The primary function is to provide stable support after a vehicle has been lifted by a jack, ensuring safety by preventing the load from falling. The design incorporates a saddle for load placement, a center column for height adjustment, a pawl mechanism for locking the height, and a control lever to engage/disengage the pawl.

Important Technical Specifications

Capacity: 6,000 lbs. (3 tons)
Minimum Lift Height: 12 inches
Maximum Lift Height: 17-1/4 inches
Range: 5-1/4 inches

These specifications indicate the maximum weight the stands can safely support and the adjustable height range they offer. It's crucial not to exceed the rated capacity to prevent damage to the stands or personal injury.

Usage Features

The manual outlines several key usage features and safety guidelines:

Safe Operation: Users are explicitly warned to read, understand, and follow all instructions and warnings before operating the tool. Failure to do so may result in personal injury, property damage, and void the warranty.
Proper Jacking Procedures: Users must refer to their vehicle's owner's manual for correct jacking procedures and lift the vehicle only on manufacturer-specified areas.
Load Support Points: The jack stands must be positioned under the vehicle at points specified by the vehicle manufacturer as proper load support points.
Height Adjustment: To adjust the stands, the control lever is held up while lifting the saddle shaft to the desired height. The control lever is then pushed down to lock the pawl into the teeth of the center column. It is critical to ensure the pawl is fully engaged into the teeth for secure support.
Paired Use: The stands must always be used in pairs.
Surface Requirements: They must be used on a hard, level surface capable of sustaining the load. Using them on uneven or soft surfaces can lead to instability and loss of load.
Load Placement: The load must be positioned only on the center of the saddle to maintain stability.
Clearance: All personnel must be clear of the load before lowering it onto the stands, and no one should pass underneath the load until it is securely supported.
Overload Prevention: Overloading the jack stands beyond their rated capacity is strictly prohibited as it can cause damage or failure.
Damage Precaution: The product should not be operated if damaged during shipment, handling, or misuse. Any damaged parts must be repaired or replaced before use.

Maintenance Features

The manual emphasizes simple yet critical maintenance procedures to ensure the longevity and safety of the jack stands:

Pre-Use Visual Inspection: Before each use, a visual inspection of the stands is required. This inspection should check for cracks, cracked welds, and any missing or damaged parts.
Immediate Removal from Service: Any stand that appears damaged in any way must be immediately removed from service. This is a crucial safety measure to prevent accidents.
No Modifications: Users are explicitly warned against making any modifications to the product. This is due to the potential hazards associated with the misuse of this type of equipment, as modifications could compromise the structural integrity and safety features of the jack stands.

The document also includes a limited warranty section, detailing the terms and conditions of the warranty, including coverage for defects in materials and workmanship, return procedures, and exclusions for consumables, misuse, neglect, accident, or unauthorized alterations. The warranty is valid for one year from the date of purchase, with specific procedures for returns within 90 days and after 90 days. It also clarifies that Performance Tool does not authorize others to make warranties or assume liability on its behalf and disclaims implied warranties except where mandated by law for personal, family, or household use.