1 YEAR LIMITED WARRANTY
PERFORMANCE TOOL® extends only the following warranties, and only to original retail purchasers. These warranties give specific legal rights.
Except where prohibited by local law, the law of the State of Washington governs all warranties and all exclusions and limitations of warranties and
remedies. There may be other rights which vary from state to state.
PERFORMANCE TOOL® warrants the product to be free from defects in materials and workmanship under normal use and service. A defective
product may be returned for a free replacement within 90 days from the date of purchase, provided that product is returned to place of purchase
immediately after discovery of defect. After 90 days and up to one year from date of purchase, PERFORMANCE TOOL® will replace at no charge
any parts which our examination shall disclose to be defective and under warranty.
These warranties exclude blades, bits, punches, dies, bulbs, fuses, hoses, and other consumables which must be replaced under normal use and
service. These warranties shall not apply to any product or part which is used for a purpose for which it is not designed, or which has been repaired
or altered in any way so as to affect adversely its performance or reliability, nor shall these warranties apply to any product or part which has been
subject to misuse, neglect, accident or wear and tear incident to normal use and service.
PERFORMANCE TOOL® does not authorize any other person to make any warranty or to assume any liability in connection with its products.
Except for warranties of title and the limited express warranties set forth above, PERFORMANCE TOOL® makes no express or implied warranties of
any kind with respect to its products. In particular, PERFORMANCE TOOL® makes no implied warranty of merchantability and no implied warranty
of fitness for any particular purpose, except that for goods purchased primarily for personal, family or household use and not for commercial or
business use, PERFORMANCE TOOL® makes an implied warranty of merchantability (and, if otherwise applicable, an implied warranty of fitness
for a particular purpose), but only for the particular qualities or characteristics, and for the duration, expressly warranted above. The laws on
limitation of implied warranties may differ from state to state, so the above limitations may not apply in all cases.
PERFORMANCE TOOL® shall not be liable for consequential, incidental or special damages resulting from or in any manner related to any product,
or to the design, use, or any inability to use the product. The sole and exclusive remedy for a defective product or part shall be the repair, or
replacement thereof as provided above. The laws on limitation of remedies or on consequential, incidental or special damages may vary from state
to state, so the above limitations may not apply in all cases.
OPERATION CONT.
INSTALLING ACCESSORIES
• Forlargeraccessories(exibleextension,longspraynozzle,squeegee),eachhasalockingtabconnectionto
ensureapropersealandsecureattachment.Toinstallanattachment:
1. Placethedesiredaccessoryontothesteamcleaner.
2. Turn slowly while pressing lightly until the tab aligns with the accessory.
3. Pressandturnclockwise.Thereshouldbeatighttafteraslightclockwiseturn.
• Forthesmallerbrushandangleaccessoriespresstheopenendontothesteamclearernozzlermly,untilaccessory
is secure. NOTE this will only engage the outer clear o-ring, not the inner red o-ring.
• Tousetheexibleextensionhose,followdirections1-3above,andtherepeataccordinglydependingonwhich
accessory you intend to use.
• Thesqueegeeandtowelaccessoriesaredesignedforusethe6in.x5in.widebrushattachment.
1. Towel–pullthetowelovertheouteredgesofthewidebrush.Itisdesignedtobeasnugt
2. Squeegee – place the two small tabs on the back end of the squeegee into the loops on the back end of the wide
nozzle,thenpressthefrontofthewidenozzlesoitsnapsintotheclipatthefrontofthesqueegee.
• Reversedirectionstoremoveanyaccessory
REFILL WATER DURING OPERATION
1. Unplugthepowercordanddisconnectthepowersupply.
2. Pressdownthetriggertoreleasethepressureuntilnomoresteamisdispensed.
3. Slowly unscrew the safety cap but do not remove it, any residual steam will be discharged slowly until no steam comes
out.Thenplacethesteamcleanerinacoolplacetocoolitdownforaboutveminutes.
4. Finally, completely remove the safety cap.
5. Usethefunnelandmeasuringcuptorellasuitablequantityofcoldorhotwaterintothetank.
6. Re-installthesafetycapontothesteamcleanerbodyandtightenitinposition.
CLEANING/STORAGE
1. Repeatssteps1-4above.
2. Emptytheresidualwaterinthetankandcleantheexternalsurfacewithapieceofdrycloth.
3. Re-installthesafetycapontothesteamcleanerbodyandtightenitinposition.
4. Notes:Re-installthesafetycapontothesteamcleanerbodyandtightenitinposition.
WARNING: NEVER REMOVE THE CAP OR ANY ACCESSORIES WHILE STEAM CLEANER IS IN USE.
Check out the collection of power tools we offer.