Performax 207-9002 - User Manual

Questions and Answers

C
Cynthia HayesAug 14, 2025
What to do if my Performax Air Compressor does not run?
- A
  Austin DaviesAug 14, 2025
  If your Performax Air Compressor doesn't start, first ensure it's properly plugged in and the power switch is ON. Check for any issues with the extension cord you're using. Replace the fuse or reset the breaker at the power supply. If the compressor has overheated, unplug it and wait for it to cool down before attempting to restart it. If the issue persists, the pressure switch may need replacement. Also, the compressor will only turn on when the tank pressure drops to the cut-in pressure.
R
rburnsAug 17, 2025
Why do the fuses blow or the circuit breaker trips repeatedly on my Performax 207-9002 Air Compressor?
- K
  Katherine SchneiderAug 17, 2025
  If fuses blow or the circuit breaker trips repeatedly when using your Performax Air Compressor, ensure the fuse or breaker at the power supply is the correct size and type. Use only time-delay fuses. Also, disconnect other electrical appliances from the circuit or operate the compressor on its own branch circuit. Make sure you are using the correct wire gauge and length extension cord.
T
Terrence RamosAug 20, 2025
Why does my Performax 207-9002 Air Compressor motor hum, but not run or runs slowly?
- J
  John LoweAug 20, 2025
  If your Performax Air Compressor motor hums but doesn't run properly, the voltage from the power supply may be low; check it with a voltmeter. Ensure you are using the correct wire gauge and length extension cord.
J
Joanne FordAug 25, 2025
Why does the thermal overload protector cut out repeatedly on my Performax Air Compressor?
- A
  Anthony WilliamsAug 25, 2025
  If the thermal overload protector cuts out repeatedly on your Performax Air Compressor, check the voltage from the power supply with a voltmeter. If the motor is overheating due to poor ventilation, move the compressor to a well-ventilated area. Also, check that you are using the proper gauge wire and cord length.
T
Timothy OneillAug 27, 2025
Why is air leaking from my Performax Air Compressor?
- W
  walterkimberlyAug 27, 2025
  If air is leaking from your Performax Air Compressor, ensure all connections are sealed with thread sealing tape and are tightened properly. If the leak persists, the air hose may need to be replaced.
C
cannonkarenAug 30, 2025
What to do if the air receiver pressure drops when the Performax 207-9002 shuts off?
- R
  Roberto FreemanAug 30, 2025
  If the air receiver pressure drops when your Performax Air Compressor shuts off, check all connections (fittings, tubing, etc.) with soapy water to look for bubbles, then tighten any loose connections until the leak stops. Also, tighten the drain valve.
C
Christopher AlvarezSep 3, 2025
Why does my Performax 207-9002 run continuously?
- F
  fmarksSep 3, 2025
  If your Performax Air Compressor runs continuously, ensure the tank drain valve is closed. Also, decrease the amount of tool run-time; the compressor may not be large enough to supply the air requirement of the tool.
J
judith32Sep 6, 2025
Why is there excessive moisture in the air discharge from my Performax 207-9002?
- M
  mingramSep 6, 2025
  If there is excessive moisture in the air discharge from your Performax Air Compressor, drain the tank to remove water. If the humidity is high, move the compressor to an area of less humidity or use an air line filter to reduce moisture discharge in the tank.
B
Benjamin HarrisSep 9, 2025
How to fix a vibrating Performax Air Compressor?
- H
  Hannah MendozaSep 9, 2025
  If your Performax Air Compressor vibrates, tighten the mounting bolts.

Summary

Product Specifications

Assistance and Support

Contact information for customer support and technical assistance.

Introduction and Safety Overview

Product Introduction

General overview of the air compressor's features and design priorities.

Critical Danger Warning

Essential safety alert regarding breathing air quality and warranty voidance.

General Safety Rules

Work Area Safety Guidelines

Maintaining a clean, well-lit, and hazard-free workspace.

Electrical Safety Precautions

Avoiding electric shock hazards related to cords, grounding, and wet conditions.

Personal Safety Measures

Staying alert, dressing appropriately, and using protective gear.

Tool Use and Care Safety

Safe practices for operating and maintaining the tool.

Service Safety Procedures

Specific Safety Rules

Hazardous Operations Safety

Rules for fire, explosion, spraying chemicals, and high pressure use.

Environmental and Electrical Safety

Avoiding water, rain, and ensuring proper extension cord use.

Understanding Safety Symbols

Electrical and Construction Symbols

Symbols for voltage, current, frequency, and construction type.

Operational Hazard Symbols

Symbols indicating risks like bursting, fire, shock, hot surfaces, breathing, injury.

Signal Word Definitions

Essential Operation Warnings

Warnings about reading the manual and using eye protection.

Electrical System and Grounding

Extension Cord Selection Guide

Chart and advice for choosing the correct extension cord wire gauge.

Electrical Connection and Grounding

Proper connection to a grounded outlet and the importance of grounding.

Glossary of Air Compressor Terms

Air Compressor Features Overview

Component Identification Diagram

Visual identification of key compressor parts.

Main Features Explained

Brief explanations of handle, gauges, and valves.

Know Your Air Compressor

Motor and Pump Operation

Explains the function of the oil-free motor and air compressor pump.

Safety Valve and Drain Valve

Describes the function of the safety valve and drain valve.

Gauges and Regulator Knob

Explains the purpose of tank pressure, regulator gauges, and the regulator knob.

Unpacking and Packing List

Steps for unpacking and items included in the package.

Assembly and Initial Setup

Attaching the Air Hose

How to connect the hose to the quick coupler.

Pump Break-In Procedure

Instructions for the initial 10-minute run to break in pump parts.

Overload Protector and Duty Cycle

Explanation of the thermal overload protector and intermittent duty cycle.

Operating the Air Compressor

Approved Applications

Lists the intended uses for the air compressor.

Using the Air Compressor Steps

Step-by-step guide on how to operate the compressor.

Operational Safety Warnings

Key safety reminders to follow during operation.

Draining the Air Tank

Checking the Safety Valve

How to test the safety valve before each use.

End of Operation and Storage

Steps for shutting down and storing the compressor.

Maintenance and Care Instructions

General Maintenance Schedule

Routine checks and draining procedures for upkeep.

Lubrication Requirements

Information on bearing lubrication for the unit's lifespan.

Troubleshooting Common Problems

Air Compressor Parts Diagram

Air Compressor Replacement Parts

Pump Unit Parts Diagram

Pump Unit Replacement Parts

Finish Nail Gun Operation Guide

Nail Gun General Safety

Basic safety rules for operating the finish nail gun.

Nail Gun Personal Safety

Specific safety precautions for the user's well-being.

Nail Gun Tool Use and Care

Guidelines for proper tool handling and maintenance.

Nail Gun Service and Air Source

Requirements for servicing and the air source for the nail gun.

Specific Nail Gun Safety Rules

Nail Gun Technical Data and Lubrication

Specifications and lubrication instructions for the nail gun.

Nail Gun Loading and Operation

Adjusting Nailing Depth

No-Mar Tip and Exhaust Adjustment

Clearing Nail Gun Jams

Procedure for safely removing jammed nails from the tool.

Nail Gun Lubrication and Parts

Performax Air Compressor Warranty

30-Day Money Back Guarantee

Details of the money-back guarantee policy.

2-Year Limited Warranty

Terms and conditions of the limited warranty coverage.

Performax 207-9002 Specifications

General

Power Source	Electric
Horsepower	2 HP
Voltage	120 V
Amperage	15 Amps
Pump Type	Oil-Free
Tank Capacity	20 gallons
Tank Size	20 gallons
Noise Level	78 dBA