PERMASTEEL PG-40612SOLE

Questions and Answers

M
michaelcarrAug 18, 2025
Why is there a sudden drop in gas flow or low flame on my PERMASTEEL Grill?
- S
  Sean BallAug 18, 2025
  A sudden drop in gas flow or low flame on your PERMASTEEL Grill can stem from a few reasons: * First, check if your LP cylinder is out of gas. * If not, the excess flow valve may have tripped. Try turning off the knobs, waiting 30 seconds, and then lighting the grill. If the flames remain low, turn off the knobs and LP cylinder valve, disconnect the regulator, reconnect it, perform a leak test, turn on the LP cylinder valve, wait 30 seconds, and then light the grill. * Vapor lock at the coupling nut/LP cylinder connection can also cause this issue. To resolve it, turn off the knobs and LP cylinder valve, disconnect the coupling nut from the cylinder, reconnect it, and retry.
R
Robert DonovanAug 21, 2025
How to stop flare-ups on PERMASTEEL PG-40612SOLE?
- S
  Sarah HoldenAug 21, 2025
  Flare-ups on your PERMASTEEL Grill can be caused by: * Drip buildup: Clean the burners and the inside of the grill/firebox. * Excessive fat in meat: Trim fat from meat before grilling. * Excessive cooking temperature: Adjust (lower) the temperature accordingly.
D
Diana WellsAug 25, 2025
What to do if flames blow out on PERMASTEEL PG-40612SOLE Grill?
- R
  Renee HendersonAug 25, 2025
  If the flames on your PERMASTEEL Grill are blowing out, consider these factors: * High or gusting winds: Turn the front of the grill to face the wind or increase the flame height. * Low on LP gas: Refill the LP cylinder. * Excess flow valve tripped: Refer to the 'Sudden drop in gas flow' section for troubleshooting steps.
D
dskinnerAug 28, 2025
What to do if PERMASTEEL PG-40612SOLE has flashback (fire in burner tube(s))?
- M
  Maria MarshAug 28, 2025
  If you experience flashback (fire in the burner tubes) on your PERMASTEEL Grill, it's likely due to blocked burner components. Turn the knobs to the OFF position and then clean the burner and/or burner tubes. Refer to the burner cleaning section for detailed instructions.
D
Daniel ColemanAug 31, 2025
What to do if PERMASTEEL PG-40612SOLE Grill has persistent drip fire?
- C
  Chris RossAug 31, 2025
  If you have a persistent drip fire in your PERMASTEEL Grill, it's likely caused by drips trapped by food buildup around the burner system. To resolve this: * Turn the knobs to the OFF position. * Turn the gas off at the LP cylinder. * Leave the lid in position and let the fire burn out. * After the grill cools, remove and clean all parts.
T
Tyler YoungSep 4, 2025
How to match light PERMASTEEL PG-40612SOLE?
- S
  sjenkinsSep 4, 2025
  To match light your PERMASTEEL Grill, use a long-stem match (fireplace match). Refer to the 'Match-Lighting' section for detailed instructions.
R
Richard CollinsSep 7, 2025
Why is one burner not lighting from other burners on my PERMASTEEL PG-40612SOLE?
- M
  Michael JacksonSep 7, 2025
  If one burner on your PERMASTEEL Grill isn't lighting from the others, it could be due to drip buildup or food particles in the end(s) of the carryover tube(s). Clean the carry-over tube(s) with a wire brush to resolve this.
A
Alec WebbSep 12, 2025
Why am I unable to fill my PERMASTEEL Grill LP cylinder?
- S
  Sean AustinSep 12, 2025
  If you're unable to fill your PERMASTEEL Grill LP cylinder, it might be because some dealers have older fill nozzles with worn threads that don’t properly engage the valve. Try a second LP dealer.
R
Rodney BentleyNov 13, 2025
What to do if PERMASTEEL Grill burner won't light using igniter?
- C
  Christopher AdamsNov 14, 2025
  If the burner on your PERMASTEEL Grill doesn't light with the igniter, there are several potential causes related to gas flow and ignition. Here's what you can check: * Ensure you're trying to light the correct burner by checking the control panel instructions. * Make sure the valves are correctly positioned inside the burner tubes. * Inspect the burner tubes for obstructions like spider webs; if present, clean them. * Verify that your LP cylinder isn't empty, and if it isn't, refer to the section on 'Sudden drop in gas flow'. * Address potential vapor lock issues by turning off the knobs, disconnecting the coupling nut from the LP cylinder, reconnecting, and retrying. * Confirm the coupling nut and LP cylinder valve are fully connected, tightening them by hand until snug. * ...