Need help?Do you have a question about the Pfeiffer Vacuum PRISMAPRO QMG 250 and is the answer not in the manual?
General| Type | Quadrupole Mass Spectrometer |
|---|---|
| Mass Range | 1 - 250 amu |
| Ion Source | Electron Impact (EI) |
| Detector | Secondary Electron Multiplier |
| Filament | Tungsten or Thoria-coated Iridium |
| Vacuum Requirements | High vacuum |
| Applications | Residual gas analysis, process monitoring, leak detection |
| Detection Limit | ppm levels |
| Interface | RS-232, Ethernet |
Document describes product functions and provides safety information.
Identifies intended audience for operating instructions.
Explains text formatting, pictographs, and abbreviations used.
Lists trademarks used in the document.
Explains risk levels (DANGER, WARNING, CAUTION, NOTICE).
Provides critical safety instructions for product life stages.
Details safety measures and responsibilities to prevent hazards.
Defines the intended application and operational guidelines for the spectrometer.
Lists uses that invalidate warranty and liability claims.
Outlines Pfeiffer Vacuum's and operator's responsibilities and warranty terms.
Specifies requirements for safe product operation and maintenance.
Defines necessary qualifications and training for personnel.
Lists essential steps for operators before and during use.
Explains how to identify the product using rating plate data.
Lists all parts included in the product shipment.
Describes how the quadrupole mass spectrometer functions.
Provides a high-level view of the system components and architecture.
Details the components and variants of the analyzer.
Describes the electronic control unit for the QMG 250.
Introduces the software for configuration, operation, and data analysis.
Details various connection interfaces for the electronic unit.
Describes the connection for the power supply unit.
Explains the Ethernet connection for PC or network communication.
Details the standard I/O interface for analog and digital signals.
Describes the extended I/O interface for advanced functions.
Explains the connection for Pfeiffer Vacuum gauges.
Notes the USB connection is for service personnel.
Provides instructions and notices for safe product transportation.
Offers guidelines for proper storage to prevent damage.
Covers essential safety and preparation steps for product installation.
Details the procedure and precautions for installing the analyzer.
Explains the steps and safety measures for installing the electronic unit.
Guides on making network and power connections.
Details how to connect the device to a PC or network via Ethernet.
Provides instructions for connecting the power supply.
Explains how to connect vacuum gauges.
Covers setting up network communication via Ethernet.
Discusses IP address configuration and potential conflicts.
Explains subnetting for IP network division.
Describes methods to modify the device's IP address.
Details how to change the PC's IP address for network compatibility.
Guides the installation process for the PV MassSpec software.
Explains how to connect the PrismaPro to a network or host computer.
Details connecting a single PrismaPro device to a network.
Covers connecting multiple PrismaPro devices to a network.
Lists prerequisites and checks before system power-on.
Provides instructions for safely powering on the device.
Refers to instructions for operating via the Web User Interface.
Refers to instructions for operating the PV MassSpec software.
Guides visual checks of the ion source before component replacement.
Details maintenance considerations for the analyzer and electronic unit.
Explains how to view the test report for parameters.
Provides instructions and warnings for the analyzer baking out procedure.
Details how to inspect and test filaments and the ion source.
Covers factory and manual mass calibration procedures.
Describes the factory calibration process for mass scale alignment.
Explains how to perform mass calibration using the TUNE function.
Guides on choosing appropriate gas mixtures for calibration.
Suggests using test gas mixtures for calibration.
Explains using process gases for calibration.
Details calibration steps for helium leak detection.
Provides instructions for replacing the filament unit.
Details replacing the filament unit for the open ion source.
Details replacing the filament unit for the cross beam ion source.
Details replacing the filament unit for the grid ion source.
Provides instructions for replacing the ion source.
Details replacing the open ion source.
Details replacing the cross beam ion source.
Details replacing the grid ion source.
Guides users on identifying and resolving common issues and malfunctions.
Outlines procedures and warnings for safely shipping the product.
Provides general guidelines for recycling and disposal of product materials.
Details the process for safely dismantling and disposing of the spectrometer.
Describes options for product maintenance and support services.
Instructs on how to order spare parts, accessories, and optional components.
Lists system components available for replacement.
Lists available ion sources and filament units for analyzers.
Details spare parts and specific kits for maintenance.
Presents detailed technical specifications for Faraday detectors.
Presents detailed technical specifications for EM/Faraday detectors.
To Next Page
