Phaze 594335 - User Manual

Item Code: 594335
4 IN 1
Jump Starter
IMPORTANT – CHARGE BEFORE FIRST USE – RECHARGE
AFTER EACH USE – RECHARGE EVERY 2 MONTHS
IN ORDER TO ENSURE CORRECT AND SAFE USAGE OF
YOUR POWER PACK READ THESE INSTRUCTIONS
CAREFULLY BEFORE EVERY USE
Phaze Tools produced for Halfords Ltd, B98 0DE.
USE OF THE 12V CIGARETTE LIGHTER SOCKETS
WARNING: Do not use this feature when the internal battery is being recharged.
These socket can be used for the operation of any 12V DC appliance (10amp maximum) fitted with
a cigarette lighter plug.
The use of this feature will discharge the internal battery so it may need recharging before jump
starting is possible. See above.
In the event of overload, remove the cigarette lighter plug from the socket and press the overload
reset button located on the rear of the starter pack.
USE OF THE 5V USB PORT
This port can be used for the charging or operation of any 5V DC appliance that uses a standard A
type USB plug. This may not be compatible with Apple and other devices. The LED next to the USB
port will illuminate when the USB port is in use. To activate this port press the button above. Press
again to deactivate.
Note:
• Always recharge this product indoors.
• Do not recharge in wet or damp conditions.
• Always use in a well ventilated area.
• Always keep this product in an upright position.
• Switch off when not in use.
• When switched on, do NOT allow red and black clamp metal parts to touch.
PRODUCT SPECIFICATION
Charger Supply Voltage 230V 50Hz. AC
Output Voltage 12V DC through battery clips & cigar sockets
Output Voltage 5V DC 0.5A through USB port
Jump Starting Current 350 Amps (intermittent recommended max.)
Internal battery 17A/h
Cigarette Lighter Socket Output 12V DC, with automatic safety cut out
Recharge 12V DC / 500mA with automatic charge cut off
This product contains a sealed lead-acid battery which should not be tampered with and should be
disposed of at a recognised recycling facility or collection point.
DECLARATION OF CONFORMITY
We declare that this product conforms to the following directives
2006/95/EC, 2004/108/EC, 2011/65/EU (ROHS), EN 61558-1:2005/A1:2009,
EN 61558-2-6:2009, EN 62233:2008, EN61000-6-1: 2007, EN61000-6-3: 2007,
EN 55014-1: 2006+A1:2009+A2:2011, EN 55014-2: 1997+A1:2001+A2:2008,
EN 61000-3-2: 2006:+A1:2009+A2:2009, EN 61000-3-3: 2008
3

Summary

Using the 12 V Cigarette Lighter Sockets

Using the 5 V USB Port

Product Specifications

Declaration of Conformity

General and Safety Information

Safety Precautions

Wear eye protection and avoid contact with battery electrolyte. Seek medical advice for burns.

Important Storage Note

Storing the Power Pack with a discharged battery causes irreversible damage.

Waste Disposal Information

Treat as WEEE. Dispose of at a local authority civic waste site for recycling.

Battery Recycling

Segregate and recycle spent batteries through collection schemes or retail stores.

Operating Instructions

Jump Starting Procedure

Connect clamps correctly, switch on, start engine, then disconnect. Avoid incorrect connection.

Recharging the Internal Battery

Recharge after use and every 2 months. Use 230V adaptor and monitor charging LEDs.

Integral Light Operation

The integral light is illuminated by pushing the button on the front panel.

Overview

1. Function Description
2. Important Technical Specifications
3. Usage Features
4. Maintenance Features

The Phaze 4-in-1 Jump Starter is a versatile portable power source designed for various automotive and personal electronic needs. It combines a jump starter, a 12V DC power source, and a 5V USB charging port, making it a comprehensive tool for emergencies and everyday use.

Function Description:

The primary function of this device is to jump-start vehicles with 12V starting systems. It provides a substantial 350 Amps of intermittent jump-starting current, capable of assisting with vehicle battery issues. Beyond jump-starting, the unit serves as a portable 12V DC power source through its cigarette lighter sockets, allowing users to operate or charge 12V DC appliances up to a maximum of 10 amps. Additionally, it features a 5V USB port, enabling the charging or operation of standard A-type USB devices, though compatibility with Apple and other specific devices may vary. An integral light is also included for convenience in low-light conditions.

Important Technical Specifications:

• Charger Supply Voltage: 230V 50Hz AC
• Output Voltage (Battery Clips & Cigar Sockets): 12V DC
• Output Voltage (USB Port): 5V DC 0.5A
• Jump Starting Current: 350 Amps (intermittent recommended max.)
• Internal Battery: 17A/h (sealed lead-acid)
• Cigarette Lighter Socket Output: 12V DC, with automatic safety cut out
• Recharge: 12V DC / 500mA with automatic charge cut off
• Compliance: Conforms to directives 2006/95/EC, 2004/108/EC, 2011/65/EU (ROHS), and various EN standards including EN 61558-1:2005/A1:2009, EN 61558-2-6:2009, EN 62233:2008, EN61000-6-1: 2007, EN61000-6-3: 2007, EN 55014-1:2006+A1:2009+A2:2011, EN 55014-2: 1997+A1:2001+A2:2008, EN 61000-3-2: 2006:+A1:2009+A2:2009, EN 61000-3-3: 2008.

Usage Features:

• Jump Starting:
  • Ensure the internal battery has sufficient charge.
  • Switch off the vehicle ignition.
  • Set the Power Pack's rotary On/Off switch to OFF.
  • Connect the red (+) clamp to the vehicle's positive battery terminal.
  • Connect the black (-) clamp to the engine or chassis (an unpainted, dirt-free, non-moving metal component, NOT a fuel line). Crucially, the black (-) clamp must NOT be connected to the negative terminal of the vehicle battery due to explosion risk.
  • Ensure leads are clear of hot or moving parts.
  • Turn the rotary On/Off switch to ON. Wait approximately one minute for charge equalization.
  • Start the vehicle engine.
  • Once started, return the rotary On/Off switch to OFF.
  • Disconnect the black (-) clamp first, then the red (+) clamp. Do not pull the cable to disconnect.
  • Important Safety Note: Incorrect connection can cause severe damage to the vehicle and the Power Pack, and may result in personal injury.
• 12V Cigarette Lighter Sockets:
  • These sockets are designed for operating 12V DC appliances (max 10A) with a cigarette lighter plug.
  • Warning: Do not use this feature when the internal battery is being recharged.
  • Using these sockets will discharge the internal battery, potentially requiring a recharge before jump-starting is possible.
  • In case of overload, remove the plug and press the overload reset button on the rear.
• 5V USB Port:
  • Used for charging or operating 5V DC appliances with a standard A-type USB plug.
  • The LED next to the USB port illuminates when in use.
  • Activate/deactivate by pressing the button above the port.
• Integral Light: Activated by pushing the button on the front panel.

Maintenance Features:

• Recharging the Internal Battery:
  • Crucial: Charge before first use, recharge after every use, and recharge every 2 months.
  • To check charge status, push the test button on the left side of the front panel. A green LED indicates sufficient charge, while yellow or red LEDs indicate a need for partial or full charge.
  • To charge, plug the 230V UK mains charging adaptor into the rear socket, then into a 230V mains socket and switch on. The 'Charging' LED will illuminate.
  • When fully charged, the charging indicator LED will turn off, and the 'Charged' LED will illuminate. Disconnect the adaptor from the Power Pack and the mains supply.
• General Care:
  • Store in a dry place, below 50°C, to avoid moisture damage.
  • Do not use if damaged or when the internal battery is being recharged.
  • Always recharge indoors, in a well-ventilated area, and not in wet or damp conditions.
  • Keep the product in an upright position.
  • Switch off when not in use.
  • When switched on, do NOT allow red and black clamp metal parts to touch.
  • Important Note: Storing the Power Pack with a discharged battery will cause irreversible damage to the battery.
• Safety:
  • Wear eye protection when working with lead-acid batteries.
  • Avoid contact with electrolyte from vehicle batteries, as it is acidic and can cause burns. Rinse affected areas with water immediately and seek medical advice if symptoms persist.
• Disposal and Recycling:
  • The product contains a sealed lead-acid battery that should not be tampered with.
  • Dispose of at a recognized recycling facility or collection point.
  • This product is marked as Waste Electrical & Electronic Equipment (WEEE) and should not be mixed with general household waste. Take WEEE marked products to Local Authority Civic waste sites.
  • Spent batteries should be collected separately for proper treatment and recycling. Contribute to battery recycling by segregating all spent batteries and participating in collection schemes.

Phaze 594335 Specifications

General

Brand	Phaze
Model	594335
Category	Remote Starter
Language	English