What to do if I cannot pull out the key from Philips Door locks?
If you cannot pull the key out from the Keyhole of your Philips Door locks, disassemble the lock, then rotate to pull out the key and re-install the lock. Do not insert the key when you are installing.
Why can I see picture but no sound is heard on my Philips Monitor?
If you can see a picture but hear no sound on your Philips Monitor, check the following: 1. Ensure both video and sound input cables are correctly connected. 2. Make sure the volume isn't turned all the way down; press the volume buttons to increase it. 3. Verify that Mute is off using the Mute button. 4. If using external speakers, ensure they are connected and the volume is at a suitable level.
How to fix a Philips Coffee Maker that does not turn on?
If your Philips Coffee Maker doesn't turn on, ensure it's properly connected to the electric network and that the power button is switched to the “I” position.
Why is the Bluetooth audio quality poor on my Philips Speaker System?
If the audio quality from a connected Bluetooth device to your Philips Speaker System is poor, it could be due to poor Bluetooth reception. Try moving the device closer to the soundbar or removing any obstacles between the device and the soundbar.
Why does my Philips Door locks rotates only if the Key is inserted?
If the Philips Door locks rotates only when the Key is inserted, ensure the Latch Bolt is installed correctly.
Why some picture elements do not light up on Philips Monitor?
This display is manufactured using an extremely high level of precision technology: however, sometimes some pixels of the display may not display. This is not a malfunction.
What to do if there is no sound from my Philips Speaker System soundbar?
If there is no sound from your Philips soundbar speaker, try the following: * Connect the audio cable from your soundbar to your TV or other devices. * Select the correct audio input on the remote control. * Ensure that the soundbar is not muted. * Reset the product to its factory settings (see 'Factory reset').
What to do if the buttons on my Philips Speaker System don't work?
If the buttons on the main unit of your Philips Speaker System do not work, disconnect it from the power supply for a few minutes, and then connect it again.
Why do I see after-images on my Philips Digital Signage?
After-images can occur if a still picture is displayed for an extended period. To prevent this, avoid displaying a still image for an extended period of time, as this can cause a permanent after-image to remain on the display.
Why is there no picture on my Philips Monitor?
There are several reasons why your Philips Monitor might not be displaying a picture: 1. The power cord might be disconnected; plug it in. 2. The main power switch on the back of the display might not be switched on; ensure it is on. 3. The selected input might have no connection; connect a signal to the display. 4. The display might be in standby mode.
General| Screen Size | 24 inches |
|---|---|
| Display diagonal | 60 cm |
| Resolution | 1366 x 768 pixels |
| Display Type | LED |
| Screen shape | Flat |
| Aspect ratio | 16:9 |
| Brightness | 200 cd/m² |
| Contrast ratio (typical) | 1000:1 |
| Dynamic contrast ratio marketing name | Mega Contrast |
| Viewing angle, horizontal | 178° |
| Viewing angle, vertical | 178° |
| Smart TV | No |
| Number of speakers | 2 |
| RMS rated power | 6 W |
| HDMI Ports | 2 |
| USB Ports | 1 |
| USB 2.0 ports quantity | 1 |
| Common interface (CI) | No |
| Common interface Plus (CI+) | Yes |
| HDMI version | 1.4 |
| VESA mounting | Yes |
| VESA mounting interfaces | 75 x 75 mm |
| Product color | Black |
| HD type | HD |
| Refresh Rate | 60 Hz |
| Digital signal format system | DVB-C, DVB-T, DVB-T2 |
| Connectivity | HDMI, USB |
| Comb filter | 3D comb filter |
To Next Page