Service Modes, Error Codes, and Fault Finding
EN 15TPM15.1E LA 5.
2015-Jun-12
back to
div.table
Table 5-2 Factory mode overview
Item Item value
Default value
Description32" 40" 50"
0 F/W VERSION Press OK Displays the software versions of the supplier, Flash PQ, Smart Picture, BL Dimming,
Source Meter, the Picture Quality checksum, the Dimming library, the Source meter
library, the Flash AQ, MCU and OAD software versions.
1 PANEL_ID See table 6-3 Display code overview Displays and changes the Panel ID with the left and right cursor; be careful changing
this, it can result in not correct displaying the screen!
2 TUNER_ID 4 Displays and changes the Tuner ID with the left and right cursor. Not to be changed
when the tuner is replaced with the correct service part.
3 DEMOD_TYPE 3 0 3 Choose demod type.
4 ERR Code: xxx xxx xxx
xxx xxx
000 000 000 000 000 Values showing the last 5 errors during the last 50 hours of operation, according to
table 5-4 Error code table
5 CLEAR ERROR BUFFER Press OK Selecting this clear all current error codes.
6 NVM ADDRESS 0 NVM address 0 to 8191, Use Item 6 to change and 7 to store the data to the correct
NVM address
7 NVM VALUE 0 Displays the value at the NVM address of item 5
8 NVM STORE Press OK Use this option to save the data of item 6 to NVM address of item 5
9 NVM COPY TV to USB Press OK Use this to store the NVM data to the REPAIR folder of a FAT formatted USB memory
stick. The TV will write two files in the REPAIR folder of the memory stick. It will create
this folder if it does not exist. The items are “Channel list”, “Personal settings”, “Option
codes”, “Display-related alignments” and “History list”. In case the download to the
USB stick was not successful “Failure” will appear. In this case, check if the USB stick
is connected properly. Now the settings are stored onto the USB stick and can be
used to download onto another TV or other SSB. Uploading is of course only possible
if the software is running and if a picture is available. This method is created to be
able to save the customer’s TV settings and to store them into another SSB.
10 NVM READ USB to TV Press OK Use this to store the NVM data from the USB memory stick to the TV. The TV will save
the two files which were created in item 8 to the NVM of the set. Use these options
when replacing a SSB. When “USB to TV Success” is displayed remove the power
and restart the TV
11 RESET_PBS_PWD Press OK Use this to reset the Child Lock
12 DIM_LIB RESET Press OK Reset the Dimming
13 SRC_METER RESET Press OK Reset the Source meter
14 AMBLIGHT RESET Press OK Reset Ambilight
15 ACFG RESET Press OK Reset ACFG
16 CIPLUS QUERY Press OK Shows the Validity of the CI+ key and the supplier information
17 CIPLUS UPDATE Press OK Used to enter a new CI+ code into the NVM. This can only be used when no CI+ code
exists in the NVM
18 EDID UPDATE Press OK Used to enter a new EDID codes into the NVM
19 TEST PATTERN Press OK With the “left” and “right” keys of the remote control various test patterns can be
chosen
20 VIRGIN_MODE Off Use this to return the set to virgin mode. Depends whether the set has been used
already.
21 E-Fuse On E-fuse mode
22 ORT_MODE Off ORT mode
23 VGA_UART_SWITCH Off When switched “on” the VGA port can be used for UART logging.
24 DRMWARNING On Warning the data rights management
25 AGEING MODE Off Off Off Use this for aging a new LCD panel
26 CLR_TEMP_R 255 223 251 Red colour temperature setting
27 CLR_TEMP_G 255 244 235 Green colour temperature setting
28 CLR_TEMP_B 255 255 255 Red colour temperature setting
29 AUTO_COLOR Press OK PC: any pattern that has black and white, YPbPr: SMPTE bar (colour bar), any timing.
30 ADC_GAIN_R 0 0 0 Red ADC gain
31 ADC_GAIN_G 0 0 0 Green ADC gain
32 ADC_GAIN_B 0 0 0 Blue ADC gain
33 ADC_OFFSET_R 128 128 128 Red ADC offset
34 ADC_OFFSET_G 128 128 128 Green ADC offset
35 ADC_OFFSET_B 128 128 128 Blue ADC offset
36 YPBPR_PHASE InValid Not available for this chassis
37 AUD_GAIN_LINEIN 0 Line-in audio gain
38 AUD_GAIN_HDMI 0 HDMI audio gain
39 AUD_GAIN_ATV 0 Analogue TV audio gain
40 AUD_GAIN_DTV 0 Digital TV audio gain
41 AUD_GAIN_USB 0 USB audio gain
42 AQ_INDEX 17 16 16 Audio Quality index
43 AUDIO TEST MODE Off Used for audio testing during production
44 AUDIO CHANNEL TYPE 0.0 Defines the installed speaker system
45 AUDIO SRS Off SRS Audio
46 DUMP PQ FROM TV Press OK Saves the picture quality data to a file “pq.bin” to the root of a FAT formatted USB
memory stick
47 LOAD PQ to TV Press OK Loads the picture quality data from a file “pq.bin” in to the TV
48 DUMP AQ FROM TV Press OK Saves the audio quality data to a file “AQ.bin” to the root of a FAT formatted USB
memory stick
49 LOAD AQ to TV Press OK Loads the audio quality data from a file “AQ.bin” in to the TV
50 COPY BIN CHL to TV Press OK Copy the USB channel list to TV
51 COPY BIN CHL to USB Press OK Copy the TV channel list to USB
52 FEF CHECK Off FEF Check
To Next Page
Loading...
