Philips AK 730 - Operation

0
0
m
PREV/NEXT: same as PREV/NEXT function of ©
and © of the CD player.
<M SEARCH W>: same as SEARCH function of®
and © of the CD player.
PLAY/PAUSE: same function as © of the CD
player.
STOP: same function as © of the CD player.
REPEAT: same function as © of the CD player.
SHUFFLE: same function as © of the CD player.
REVIEW: same function as © of the CD player.
PROGRAM: same function as © of the CD
player.
OPERATION
Warning
• Check that you have removed the red transit
protection clamp on the underside of the player (but
refit it during further transport).
• Always remove the CDs from the player before
moving the unitI
TO PLAY DISCS
• Switch on the CD changer using the POWER
ON/OFF switch ©.
• Press OPEN/CLOSE © to open the CD tray ©
• Holding the disc between the thumb and fingers of
the outstretched hand, remove it from the packaging
(Fig. 3) and place it with the label uppermost in the
tray © (Fig. 5). Both standard 12 cm (5") discs and
8 cm (3*) discs (CD singles) can be used.
• Use the PREFERRED POSITION in the tray, when
you insert only one disc.
• When you wish to insert more discs, press the
LOAD button ©to rotate the turntable in the tray.
• Press the OPEN/CLOSE button ©to close the tray
©
• Press the PLAY/PAUSE button ©. The CD of the
preferred position will now be played.
• To play another CD, select the desired disc
number with one of the DISC SELECT buttons ©.
Play begins automatically within a few seconds. In
display ©you can always see which disc and which
track are being played. Play will stop after the last
disc.
Important
If an E (for Error) appears in the display, the CD-player
cannot read the disc. Possible causes are:
—you inserted the CD the wrong way: the label should
face up (Fig. 5);
- the surface of the disc is badly scratched or dirty,
see ’Maintenance';
- the lens is steamed up because of a sudden
transition from a cold into a warm environment; do not
clean the lens, but let the set acclimatize for a while.
Changing discs during play
• Press OPEN/CLOSE © to open the CD tray ©
Two discs can now be changed.
• Press the LOAD button ©to rotate the turntable in
the tray, after which the other two discs can be
changed.
Selecting a different disc during play
• Press the desired number of the DISC SELECT
buttons ©.
In display © the disc number will appear and shortly
afterwards the first track of the chosen disc will start
to play.
Selecting a different track during play
• Press SEARCH NEXT © (or PREV SEARCH ®)
until the required track number appears in the
display.
- Shortly after this, the chosen track will start playing.
Starting again with the track that is currently
playing
• Press PREV SEARCH ©once.
- The track will be started again from the beginning.
Searching for a passage during play
• Hold SEARCH NEXT © or PREV SEARCH ®
pressed down to search for the required passage. If
you release the button, play will continue.
Repeating play
• During play press REPEAT © The REPEAT
indication lights up.
- All discs are played and then repeated.
• Press REPEAT again to stop the repeat function.
The REPEAT indication goes out.
- Play continues as normal.
• REPEAT can also be used during a PROGRAM,
SHUFFLE, and INTROSCAN.
Introscan
The INTROSCAN function can be used in both STOP
and PLAY modes by pressing the INTROSCAN
button © SCAN will then appear in the display.
The INTROSCAN function causes the first few
seconds of every track of all CDs to be played (in
PAY mode only the remaining tracks). After playing
the opening seconds of a track the CD player jumps
to the beginning of the next track. The corresponding
track number appears in the display ©
• Pressing the PAY/PAUSE button © cancels the
INTROSCAN function. The CD plays normally from
the current track onwards.
• If you press the SEARCH NEXT button @ or the
PREV SEARCH button © the unit remains in the
INTROSCAN function and the first few seconds of the
4