Philips CD 840 - Page 6

THE INDICATIONS ON THE DISPLAY (Fig. 6)
Each Compact Disc has, along with the music, a list detailing the
numbers of the tracks, the playing time of each track and the total
playing time of the disc. The player always scans this first and
stores it in its memory in order to provide information via the
display.
PLAY
> Lights up above DIRECT when the player is put in the direct play
mode.
PROGR
> Lights up under DIRECT when the player is put in the direct
programming mode.
TRACK
Under this indication you will see:
> What track is being played.
> The number of tracks on the disc after it has stopped.
> The number of tracks in a program.
TRACK TIME
Under this indication you will see:
> The elapsed playing time of the track being played.
> The total playing time of a disc or program.
REM TRACK TIME
> Indicates the remaining playing time of the track being played.
TOTAL REM TIME
> Indicates the remaining playing time of a disc or program.
MODE
Indicates the following functions:
- FTS MEMO 1 or FTS MEMO 2
> Flashes after FTS 1 or FTS 2 has been pressed.
> Lights up when a program from the FTS memory is played.
- TITLE
> Lights up after the TITLE button has been pressed.
- RANDOM
> Lights up when the tracks on the disc are played in random
order.
- REPEAT
> Lights up when you repeat a disc or program.
- REPEAT A-B
> Lights up when a passage is repeated.
*1-20’ track number indicator
> Shows the number of tracks on the disc after the track list has
been scanned.
’ + 20 *
> Lights up when there are more than 20 tracks on a disc.
READING
> Lights up when you switch the player on and when the disc’s
track list is being scanned.
8 CM DISC
> Lights up when a 8-cm disc is loaded.
12 CM DISC
> Lights up when a 12-cm disc is loaded.
PLAY
> Lights up while a disc is playing.
GO INTO STOP
> Lights up if you try to activate a function for which you must first
stop play.
GO INTO PLAY
> Lights up if you try to activate afunction for which you must first
start play.
ERROR
> Lights up if you make a mistake when operating the player.
PLAYING THE ENTIRE DISC (PLAY/REPLAY)
• Press ON/OFF to switch the player on.
> READING lights up, followed by INSERT DISC.
• Press OPEN or OPEN/CLOSE (on the remote control) to open
the disc tray.
> TRAY OPEN lights up, followed by INSERT DISC.
• Load a disc into the tray with the printed side facing upwards
(Fig. 7-9) and close the fray.
> TRAY CLOSE lights up, followed by READING.
> PLA / l i gh ts up and playback starts.
You can also press PLAY/REPLAY immediately after inserting
the disc; the tray then closes automatically.
> The number indicator shows how many tracks are on the disc.
When a track has been played its number disappears.
> Under TRACK is always shown what track is being played.
> Under TRACK TIME the elapsed playing time of the track being
played is always shown.
> After the last track play stops.
> 8 CM DISC or 12 CM DISC lights up, followed by DISC READY.
> The display shows the number of tracks and the playing time of
the disc.
ADJUSTING THE BRIGHTNESS OF THE DISPLAY (DIM)
• Hold DIM pressed down.
> BRIGHTNESS lights up.
> The brightness of the display will now decrease gradually from
the set (maximum) level.
> The successive steps are shown on the display (from ’8’ to ’1 ’).
• Release the button as soon as the required brightness level is
obtained.
• Press DIM again.
> The brightness will now increase up to the maximum level (’8’).
The brightness set using DIM is cancelled again if the player is
switched off.
CALLING UP OTHER TIME INFORMATION (TIME)
• Press TIME whenever you want to know the remaining playing
time of a track.
> REM TRACK TIME lights up.
• Press TIME again if you wish to knowthe remaining playing time
of the entire disc.
> TOTAL REM TIME lights up.
• Press TIME again if you wish to return to the elapsed playing
time indication.
> TRACK TIME lights up again._
GOING BACK TO THE BEGINNING OF A TRACK
(PLAY/REPLAY)
• Press PLAY/REPLAY.
> The track starts again from the beginning.
4