Philips CD 840 - Page 9

PLAYING THE PROGRAM
• Press PLAY/REPLAY.
> PROGRAM PLAY lights up and playback starts with the first
number of the program.
All buttons can be used during programmed play. Search for a
particular passage is only possible within the track being played.
As soon as you reach the beginning of the track, BEGIN OF NR
lights up; when you reach the end the track, END OF NR lights up.
As long as the player is in the direct programming mode you can
continue to add to the program during playback. When STOP/CM
is pressed or when the program has been played, the disc stops,
but the program remains stored. The program will be erased when
you open the tray or if you press STOP/CM twice in succession
during playback .__ _
FAVORITE TRACK SELECTIONS (FTS)
For each disc you can store two programs in the player’s
permanent (FTS) memory.
Your Favorite Track Selections of a given disc can then be called
up and played whenever you wish.
The selections will remain stored in the FTS memory even if you
play the entire disc or compile a different program from it.
The number of discs which can be stored in the FTS memory
depends on the number of tracks in each program._
STORING A FAVORITE TRACK SELECTION
• Compile your program as described in the PROGRAMMING
section.
• Press FTS 1.
> FTS MEMO 1 starts flashing.
• Press STORE.
> STORED lights up, followed by the ranking number of this
program.
> The selection is now stored in the FTS 1 memory under this
ranking number.
If you wish to store a further selection from the same disc:
• Press STOP/CM. (If you have stored the first program during
playback you must press STOP/CM twice.)
• Compile your program as described in the PROGRAMMING
section.
• Press FTS 2.
> FTS MEMO 2 starts flashing.
• Press STORE.
> STORED lights up, followed by the ranking number of this
program.
> The selection is now stored in the FTS 2 memoryojnder this
ranking number.
Notel
- If a selection of a particular disc had already been stored, then
It is automatically erased and the new selection is stored under
the old ranking number.
- If NO SPACE appears after you have pressed STORE, then the
FTS memory is full: you must erase one or more old FTS
programs to make room to store the new program.
- If NO PROGRAM appears after you have pressed STORE, then
no program has been compiled first._
FTS PROGRAMMED PLAY
• Press FTS 1 or FTS 2.
> FTS MEMO 1 or FTS MEMO 2 starts flashing.
• Press PLAY/REPLAY.
> FTS MEMO 1 or FTS MEMO 2 now lights up continuously.
> PROGRAMPLA Ylights up and the chosen selection will now be
played.
If NOTIN FTS 1, NOT IN FTS 2 or NO FTS FOUND appears, no
favorite selection has been stored.
• Press STOP/CM twice if you wish to revert to normal play.
All buttons can be used while a favorite selection is being played.
Search for a passage is only possible in the track which is being
played. As soon as you reach the beginning of the track, BEGIN
OF NR lights up; when you reach the end the track, END OF NR
lights up.
As long as the player is in the direct programming mode you can
continue to add to the program during playback._
CHECKING THE FTS MEMORY
• Press INFO.
> FTS INFO lights up.
> The following information appears on the display in this order:
- The number of discs in the FTS 1 and FTS 2 memory. For
example: ’ FTS1 04 DISC’ a n d ’FTS2 05 DISC’.
If the FTS memory is empty, then you will see * FTS 1 EMPTY’
and/or ’FTS 2 EMPTY’.
- The number of spaces available in the memory. For example:
’112 SPACE’.
- The number of times that the discs in the FTS 1 and FTS 2
memory have been played: FTS1 INFO , followed by, for exam¬
ple, ’NR 01 03 PL’, ’NR 02 05 PL’, etc.
FTS2 INFO, followed by, for example, ’NR 01 04 PL’,
’NR 02 06 PL’, etc.
- Then TITLE MEMORY appears. You are now given information
on the ’names* which you have given to discs and/or track
numbers. For this refer to ’NAMING DISCS ANG>’TRACK
NUMBERS’ under ’OTHER POSSIBILITIES’.
With NEXT you can proceed more rapidly to the next block of
information.
ERASING A FAVORITE TRACK SELECTION
• Press INFO.
> FTS INFO lights up.
• Press NEXT until the ranking number appears on the display;
for example ’NR 02 01 PL’.
• Hold CLEAR pressed down until DELETED lights up.
> The selection has now been erased.
If you do not know the ranking number:
• Load the disc and close the tray.
• Press FTS 1 or FTS 2.
> FTS MEMO 1 or FTS MEMO 2 starts flashing.
• Hold CLEAR pressed down until DELETED lights up.
> The selection has now been erased.
ERASING THE ENTIRE FTS MEMORY
• Press FTS 1.
> FTS MEMO 1 starts flashing.
• Hold CLEAR and REPEAT pressed down.
> CLEARING ALL lights up, followed a few moments later by ALL
CLEARED .
> The entire FTS memory has now been erased._
7