Philips CD 850 - Programming Features; Programming Methods; Programme Management

Before storing a programme first select either:
ADD-IN programming: store the tracks which are to be played and
their order. Up to 30 tracks can be stored in this way. Or:
TAKE-OUT programming: erase the track numbers you do not want
to hear. Now you can store as many numbers as there are tracks
on the CD.
e Press PRESET.
e Press S(tore) until POS PROG or DEL PROG appears.
e Select POS PROG (= add-in) or DEL PROG (= take-out) by
using CURSOR P.
e Press S(tore).
e Press PRESET.
@ Set the player to the direct programming mode (DIRECT PROG)
using DIRECT PROG/PLAY.
NOTE!
— Index numbers cannot be stored.
— Once you have started programming in one of the two ways, you
can no longer switch to the other way.
ADD-IN PROGRAMMING (STORE)
e Key in the required numbers; every number you key in will be
directly included in the programme.
— Each time you key in (— store) a track number, the number of
tracks and the playing time of your programme will be shown
under TRACK and TRACK TIME; if the programme is longer than
99 minutes and 59 seconds, then —— : — — lights up.
— The track number indicator always shows which numbers have
been stored.
You can also store the tracks during play; as soon as you have
entered (= stored) the first number, play continues with the
programmed track numbers.
TAKE-OUT PROGRAMMING (CLEAR)
e Key in the numbers you wish to omit; every number you key in will
be erased directly.
— Each time you key in (= erase) a track number, the remaining
tracks and their playing time will be shown under TRACK and
TRACK TIME.
— The track number indicator always shows which tracks remain for
inclusion in your programme.
You can also key in (= erase) the tracks numbers during play.
STORING A PROGRAMME USING SCAN
e Press (FAST and) SCAN before or during play.
~ (FAST) SCAN(NING) lights up.
— The first 10 or 20 seconds of each track are played in turn.
e Now you can compile your programme:
Add-in
e Press S(tore) ateach track you wish to include in the programme.
— The programmed numbers appear on the track number indicator.
Take-out
e Press C(lear) at each track you do not wish to include in the
programme.
— The erased numbers disappear from the track number indicator.
PROGRAMMING
CHECKING THE PROGRAMME (REVIEW)
e Press REVIEW prior to, during or after programmed play.
— PROG(ram) REVIEW lights up.
— All the numbers appear in the programmed sequence under
TRACK.
NO PROGRAM lights up if no track numbers have yet been stored.
PLAYING THE PROGRAMME (PLAY/REPLAY)
e Press PLAY/REPLAY.
— PROGRAM PLAY lights up and playback starts with the first
number of the programme.
All keys (except EDIT, PRESET, TITLE and INFO) can be used during
programmed play. Search for a particular passage is only possible
within the track being played.
As long as the player is in the direct programming mode you can
continue to add to the programme during playback.
ERASING A PROGRAMME (STOP/CM, OPEN or OPEN CLOSE)
€ Press STOP/CM twice or, if the CD has already stopped, just
once; you can also press OPEN or OPEN CLOSE straight away.
— [he programme has now been erased.
ERASING A TRACK FROM THE PROGRAMME (CLEAR)
e Setthe player to the direct programming mode (DIRECT PROG)
using DIRECT PROG/PLAY.
e Press REVIEW before or after programmed play (STOP mode).
— PROG(ram) REVIEW lights up.
— All the numbers appear in the programmed sequence under
TRACK.
e Press C(lear) as soon as the number you wish to erase appears.
— [he number disappears from the number indicator; it has now
been erased.
~