Philips D 6920 MK 2 - Page 3

lower
scalé
of
meter
@.
The
pointer
of
meter
@
should
‘deflect
into
the
black
area
of
this
scalé.
@
The
battery
supplyis.
switched
off
wie)
the
mains
lead
is
Connected
to
socket
@.*.
-§
=)
os
e
Before
connecting
the.
carder
to
the
mains;
ensure:
that
the
voltage
on
the
type
plate
corre=
sponds
to
your
local
mains
supply.
Contact
your
dealer
if
it
is
not
in
acoprdancg
with
yo
mains
voltage.
—
@
Now
insert
the
mains
lead
into
socket
@
and
the
_
mains
plug
into
the
wall
socket.
@
To
disconnect.
the
set
from
the
mains
com=
pletely,withdraw
the
mains
plug”
from
the
wall
-
socket.
e
@
Disconnect
the
mains
5
lead
from
socket
64
@
if
you
wish
to
use
the
battery
supply:
Important note for users in U.K:
When
fitting
a
mains
plug
to
the
mains
lead
proceed
as
follows::
The
wires
in
the
mains
lead
are
coloured
in
accordance’
with
the
following
code:
Blue
=
Neutral,
Brown
=
Live.
As
these
colours
may
not
correspond
with
the
colour
markings
identifying
the
terminals
in
your
plug
proceed.as
foliows:
The
Brown
wire
must
bé
connected
to
the
terminal
which
is.
marked
with
the
letter
L
or
coloured
Red:
The
Blue
wire
must
be
connected
to
the
terminal
which
is
marked
with
the
letter
N
or
coloured
Black.
Note:
This
apparatus
must
be
protected
by
a
SAmp
Fuse
if
a.
13
Amp
plugis
used
or
if
any
other
type
of
plugis
used
by
a5
Amp
Fuse
either
in
the
plug
or
adaptor
or
at
the
distribution
board.
If
in
doubt,
consult
a
qualified
electrician.
INTRODUCTION
TO
RECORDING
.
@
The
recording
of
radio
programmes
and
copying
of
gramophone
records
is
permissible
only
insofar
as
copyright
or
other
rights
of
third
parties
are
not
thereby
infringed.
—
Note
for
users
in
U.K::
‘Recording
and
playback
of
material
may
require
consent.
See
Copyright
Act
1956
and
The
Performers’
Protection
Acts
1958
to
1972.
Adjustment
for
type
of
tape
in
use
Before
recording
and
playback
of
sound,
it
is
‘necessary
to
adapt
the
recorder
to
the
type
of
tape
which
is
used.
The
correct
setting
is
carried
out
with
switch
(6...
@
When
using
Ferro
or
Ultra
Ferro
cassettes
(IEC
typeI),
set
switch
@@
to
"Normal
(I).
@
When
using
Chromium
cassettes
(IEC
as
Il);
set
switch
@
to
’CrO,’
(I).
e@
For
PLAYBACK
of
Metal
cassettes
(IEC
type
IY),
-
set
switch
46
to
'CrO,’
(Il).
Recording
possibilities
and
connections
Fig. 2, 8 and 9 ;
-@
Stereo
recordings
via
the
rilerdohone
baste
@3
and
@
can
be.
made,
when
using
two
micro=
phones.
Mono
recordings
on
both
channels
can
be
made
when
only
one
microphone
is
connected
to
the
right
channel
microphone
socket:
Set
selector
switch
(@
to
the
ON’
position.
- @ Recordings via the line in sockets '@) or DIN
socket @ can be made when these sockets aré
connected to the line out sockets of a radio,
amplifier, second recorder etc..*-- - ~
Note: Selector switch @ @ dings be in the “OFF”
position in this case! .
@ Mixing of signals frovh the misrophones with a. |
sound sourcé connected to the line in sockets ®
or DIN socket €9 is also possible: 7
Set selector switch @ to the ‘ON’ position.
At the same time, thé line-in signal is. recuced 19
obtain a ‘background effect’.
The balance between both signals dépands, on ‘the
’ volume of thé sound applied to the microphones —
and on the other hand of thé output level of the
sound ‘source which is connected to the line in
sockets
@)
or
DIN
socket
@0.
If
this
sound
source
has a variable output level, trial recordings can be
made to obtain the best mixing résults..-.
Note: When only one microphone in ’R/MONO’ is
used
for
mixing
of
signals,
the
stereo
channels
of
the
other
sound
source
will
be
recorded
in
mono
as
well.
@
You
may
choose
between
automatic
and
manual
recording
with
selector
switch
@).
During automatic recording, there is no need to
check or adjust the recording level. During manual
recording,
you
may
alter
the
strength
at
which.
different sounds are recorded. You may also add a
blank part between two recordings by setting the
recording level controls @ at ’min’ during record-
ing:
@
The
built-in
loudspeaker
is
switched
off
Wien
monitoring
through
headphones
connected
to
socket
(i).
Remote control
When connecting a remote control unit (e.g. the
N 6721) to socket @9, all tape transport funciions
can be remote controlled.
The tape transport buttons of the recorder remain
operative | in the usual way.
RECORDING «
@ Switch on the set with on/off (‘power ")s switct 8.
@ Open cassette holder @ with eject button @ and
insert a cassette of the IEC type I (’Nomnal’,
’Standard’ or ’Ferro’) or IEC type II (’Chromum’)
with the full reel on the left-hand side as shown in
Fig. 4. Then close the cassette holder.
e Adjust the tape type concerned with switch
e@ To start recording, press record button @ @ and
then play button ©).
e During manual recording the recording level is
set
with
the
controls
@3
in
such
a
way
that,
daring