Philips DCC 300 - Dolby Noise Reduction for ACC; Marker Functionality During Playback; Headphone Connection and Volume; Recording Process Initiation

ISOS Tamera
Biaenenemnmmmncne
eens Seearots
crore
3.
Dolby
Noise
Reduction
(NR)
ee) | Dolby only works with ACC
ae With the DOLBY B/C NR key you can choose between 2
different
modes.
Either
‘DOLBY
B’
or
‘DOLBY
C’.
To
call
the
next
mode,
press
the
same
key
again.
Example:
OFF + DOLBY B ~ DOLBY C > OFF
‘DOLBY
NR’
is
a
noise
reduction
system,
which
can
suppress
tape
hiss.
If
the
‘ACC’
has
been
recorded
with
‘DOLBY
B,
it
should
also
be
played
back
with
‘DOLBY
B’.
Dolby
noise
reduction
system
manufactured
under
license
from
Dolby
Laboratories
Licensing
Corporation.
‘DOLBY
NR’
and
the
double
D symbol
DU
are
trademarks
of
Dolby
Laboratories
Licensing
Corporation.
4. Markers
During
‘PLAYBACK’
the
unit
automatically
responds
to
various
markers
and
to
the
beginning
of
the
cassette
(for
better
understanding
see
chapter
‘MARKERS’.
5. Headphones
The
‘DCC
300’
has
a
headphone
connection
at
the
front,
suitable
for
6,3
mm
‘JACK
PLUG’.
If
your
headphones
are
equipped
with
such
a
plug,
you
can
connect
it
to
the
jack.
Adjust
the
volume
by
means
of
the
VOLUME
adjusting
knob.
12
SADE LIPPMAN IAS
atatalatetntatetatetosetatvrente
pecan emanoni a
Remember: The prerecorded DCC and |
the ACC can not be used for recording!
There are two different ways to start the recording.
The following is the easier method.
We advise to use the following method if you want to
e make a recording on a blank DCC,
® resume a recording on a partially recorded DCC,
¢ completly overwrite an already recorded DCC.
This procedure will ensure the correct recording of time and
tracknumbers on the tape.
The two major controls that are used to make a recording are
the APPEND and RECORD keys. |
Switch the unit on.
Open the cassette compartment. .
Correctly insert the cassette.
Close the cassette compartment.
The unit automatically identifies the inserted cassette.
Press the APPEND key.
The ‘APPEND’ function can only be called from ‘STOP’
or “RECORD PAUSE’ mode.
The deck searches for the start of the tape or for the
end of the last recording.
The display shows:
SIDE El
rIicirirl” ni
Pf fF ELEM
232
TI
a
DIGITAL
lf the ‘DCC’ is new or blank, the unit rewinds to the
beginning of the cassette, to write a ‘LEAD IN
MARKER’ (see chapter ‘MARKERS’ on the tape.
e lf you want to overwrite a ‘DCC’, the tape has to be
rewound to the beginning (before the ‘LEAD IN
MARKER’) before you press the APPEND key (see
chapter ‘MARKERS’).
e |f you want to add a recording to a partially recorded
DCC make sure that the tape is not at the very
beginning but after the ‘LEAD IN MARKER‘ before you
press the APPEND key (see chapter MARKERS’).
When a suitable position has been found, the unit plays
the last few seconds of the previous recording. This
function permits you to controi the position.
lf the position is not the desired one, press again the
APPEND key.
The display shows for instance:
TOTAL
(4
TRACK SIDE
_! i Se
L WRREAUAQUUONEEEAOORONOLO
Ro SHRASVANERERSININTIEREIN
DIGITAL -dB 60 50 40 30 25 20 15129 6
4 2 0