EasyManua.ls Logo

Philips DVDR5350H/02/19 - Directions for Use

Philips DVDR5350H/02/19
14 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
EN 12
3139 785 31540
5. Directions For Use
The following except of the Quick Use Guide serves as an introduction to the set.
The Complete Direction for the Use can be downloaded in different languages from the internet site of Philips Customer care Center:
www.p4c.philips.com
5.
Directions For Use
From
a
n off-
a
ir
a
nt
e
nn
a
or
cable
b
o
x
Setup External Receiver 1
Has the External Receiver 1 changed to Programme
Number 101?
Television (rear
)
Phili
p
s Recorder
(
rear
)
Television
(
rear
)
V
C
R
o
r
s
imil
ar
device
(
rear
)
Positionin
g
of G-LINK transmitte
r
set-to
p
bo
x
G
-LINK
t
r
a
n
s
mi
tte
r
Television
(
rear
)
T
o
sou
r
ce
Se
(
GUIDE
(rear)
p
p
From an off-air
antenna or
cable box
Basic connection
Before connecting
Unplug the antenna cable that is currently
connected to yo
ur TV.
Connecting
Connection with VCR
or similar device
Before connecting
Your new Philips Recorder replaces the VCR for
your recording needs. First, unplug all the
connections from your VCR.
Connecting
1
Follow step 1 to 4 of 'Basic connection' to
connect this recorder before you proceed to
step 2 below.
2
Use another scart cable (not supplied) to
connect the EXT2
AUX-I/O Scart socket on
this recorder to the SC
ART OUT socket on
your VCR.
3
Connect the power cable from the VCR to an
AC power outlet.
Note In this setup, the VCR cannot record
TV programmes.
Connection with set-top box
Your new Philips Recorder provides a G-LINK
transmitter which allows you to control the
tuner of the set-top box (satellite receiver, cable
TV box) through the GUIDE Plus+ system. Yo
u
can record the TV programmes that are received
through the set-top bo
x.
Connecting
1
Follow step 1 to 4 of 'Basic connection' to
connect this recorder before you proceed to
step 2 below.
2
Connect the supplied G-LINK cable to the
G-LINK socket on this recorder.
3
Place the G-LINK transmitter in front of your
set-top box in such a way that it can acquire
the signal broadcasted by the transmitter
.
4
Connect the power cable from the set-top
box to an AC power outlet.
Finding the viewing channel
1
Press STANDBY-ON on the recorder.
The recorder will displa
y ‘IS THE TV ON?’.
2
Switch on the TV.
You should see the { EASY SETUP } menu.
Note If connected to your VCR, make sure it
is turned off before proceeding.
3
If not, press the Channel Down button on
yo
ur TV's remote control repeatedly (or AV,
SELECT button) until you see the menu. This
is the correct viewing channel for the recorder.
Start basic setup
Use the recorder's remote control and follow
the on-screen instructions to complete the
installation.
1
Select the desired menu language, your
country and the TV shape
.
Note Select { Done } in the menu and press
to go to the next screen.
2
Activate automatic channel search.
3
Check the date and time and press .
4
To continue with the GUIDE Plus+
installation, select { Continue } and press
.
Otherwise, select { Do not install now } and
press . Wait until the recorder has finished
initialising the system, then press again.
Install the GUIDE Plus
+
system
1
Enter your language, country and postal code
To change,
press and follow the on-screen
instructions.
Install the set-top box
If you do not have a set-top box, skip ‘D’ and go
to
‘E’.
1
Press DOWN to select ‘External
Receiver
1’ and press .
2
Press again to continue.
3
Select the type of reception, service provider
and brand name of the connected set-top bo
x.
Note Press to go to the next screen.
Select { None } if none of the entries are
applicable
.
4
Select the recorder socket through which
your set-top box is connected (e.g. 'EXT2' for
EXT 2 AUX-I/O socket) and press
.
5
Turn on your set-top box and select channel
number 02 on the set-top bo
x.
6
Read the instructions on the TV and press .
7
The recorder will now attempt to change the
set-top bo
x’s channel through the G-LINK
transmitter. If the set-top box has switched to
the same programme number as displa
yed on
the TV, select {
Yes } in the menu and press .
Note If not, select { No } and press to try a
different code
.
8
Your set-top box is now installed.
Load the TV listing data
1
Press the GREEN button to leave the
menu.
Note To switch the GUIDE Plus
+
system’s host
channel manually, go to { Host Channel Setup }.
2
Press GUIDE to exit the GUIDE Plus
+
system. Leave the recorder in 'standby' mode
and turn 'on' the set-top box overnight to
collect the TV listing data, this may take up to
24 hours.
Note If you tune to your Host Channel
before going to 'standby' mode, this recorder
will start immediately to download the TV
listings data.
3
Check the { Editor } screen the next day to
ensure the source and programme numbers
are matching for all channels.
1
Disconnect the antenna cable from your TV
and connect it to the ANTENNA socket
on this recorder
.
2
Use the supplied RF coaxial cable to connect
the TV socket on this recorder to the
Antenna In socket on your TV
.
3
Use the supplied scart cable to connect the
EXT1 TO
TV-I/O Scart socket on this
recorder to the SC
ART IN socket on your TV.
Note See the accompanying user manual for
others possible connection (e.g. HDMI,
Component Video).
4
Connect the power cable from the recorder
to an AC power outlet.
Start with the 'Basic connection'.
If you have a VCR, follow the instructions for ‘Connection with VCR or similar device’.
If you have a set-top box, follow the instructions for ‘Connection with set-top box’.

Table of Contents

Related product manuals