2-8
Brief Operating Instructions
BASIC FUNCTIONS
14
• Press either CD 1, CD 2 or CD 3 to select a particular disc.
Selecting a track during playback
• Rotate í JOG CONTROL ë (pressí or ë on the remote
control) to skip to the beginning of the previous or next track
on the selected disc.
yPlayback continues with the selected track.
Selecting a track when playback is stopped
1 Rotate í JOG CONTROL ë (pressí or ë on the
remote control) to skip to the required track number.
2 PressÉ PLAY/PAUSE (Éon the remote control) to start
playback.
yPlayback starts with the selected track.
Note: Instead of using
í
or
ë
on the remote control, you can
also directly key in the required track number by using the
numerical keys. For 2-digit numbers, press the keys in
rapid succession.
Searching for a passage during playback
1 Keep à SEARCH or á SEARCH (à or á on the remote
control) pressed to find a particular passage in a backward
or forward direction.
ySearching is started and playback continues at a low
volume. After 3 seconds, the search speeds up with
volume muted.
2 Release the key at the desired passage.
yNormal playback continues.
Note: During
SHUFFLE
, while repeating a track or while playing
a program, searching is only possible within the current
track.
Repeating a track, the disc or the program
1 Repeatedly press REPEAT on the remote control during
playback to select either:
yREPEAT TRACK: The current track is played repeatedly.
yREPEAT DISC: The entire selected disc is played repeatedly.
yREPEAT ALL: All discs in the CD changer (or the program)
are (is) played repeatedly.
2 Playback starts in the chosen mode.
3 To return to normal playback, press REPEAT on the remote
control until the display indication disappears.
Note:
REPEAT DISC
is not possible during
SHUFFLE
or while
playing a program.
Playing tracks in random order
1 Press SHUFFLE on the remote control during playback.
ySHUFFLE is shown and either all tracks of the program or
of the loaded disc(s) in the CD changer or CD recorder
are played in random order.
2 To return to normal playback, press SHUFFLE again.
CD text
SHUFFLE and REPEAT
Selecting a track and searching
Selecting a disc on the CD changer
English
PROGRAM
15
You can select tracks and store them either in the CD changer
or CD recorder memory. If you use the program for playback
you can choose one of the two memories, else if you like to
specify tracks for recording, use the CD changer memory only!
You can store any track more than once.
1 Load the desired disc(s) in the disc tray(s).
2 Press either CD 1, CD 2, CD 3, or CDR to select the disc.
3 Press PROG on the unit (PROGRAM on the remote control).
yPROG starts blinking and Program is displayed.
4
If either CD 1, CD 2 or CD 3 is selected:
Rotate í JOG CONTROL ë to select either:
yCD1 (or 2, 3) All: All tracks of CD 1 (or 2, 3) will be
programmed.
yCD1 (or 2, 3) and track number: The track number of
CD 1 (or 2, 3) will be programmed.
If CDR is selected:
Rotate í JOG CONTROL ë (press the numerical keys on
the remote control; for 2-digit numbers, press the keys in
rapid succession) to select a track number.
5 Press YES to store your selection in the memory.
yThe number of programmed tracks (STEP), Prog and the
total program time are displayed. The track number
blinks in the music calendar.
6 Select and store all desired tracks in this way.
7 Press PROG on the unit (PROGRAM on the remote control)
to end programming.
yPROG stays shown and the program is currently
available.
Note: If the maximum number of programmable tracks is
reached, the display shows
Program full.
1 If necessary, press Ç STOP on the unit (Ç on the remote
control) to stop playback.
2 Press either CD 1, CD 2, CD 3, or CDR to select the desired
memory.
3 Press PROG (PROGRAM on the remote control), followed by
à SEARCH or á SEARCH (à or á on the remote
control) to move through the program steps.
yThe track number at the selected step and the total
program time are displayed.
4 Press NO to remove the track from the program.
yCleared is displayed briefly.
yThe next programmed track number will move up to this
position and is displayed together with the step number
and the remaining total program time.
1 If necessary, press Ç STOP on the unit (Ç on the remote
control) to stop playback.
2 Press NO.
yClear Prog? is displayed.
3 Press YES to clear the program.
yProg Cleared will be displayed and PROG goes off.
Note: When you open the CD recorder tray or the CD changer
tray the respective program will be cleared.
1 Select and store all desired tracks in the CD changer
memory (see “Programming track numbers”).
2 Enter the recording menu (see “Internal recording”).
• If the total time of the program is of larger size than the
remaining recording time of the CDR(W):
yNot fitting! will be displayed briefly, followed by
the remaining recording time and Record Prog?
If you nevertheless start recording, only those tracks of the
program that fit onto the CDR(W) will be recorded in
entirety.
•To change the program, press NO.
yEdit Program will be displayed briefly, PROG and
the time of the program start blinking. Now you can
change the program (see “Programming track numbers”,
“Erasing a track from the program” and “Clearing the
program”).
Making a program for recording
Clearing the program
Erasing a track from the program
Programming track numbers
English
MIC
MIC
LEVEL
REC TY
EDIT
COMPILE CD
FINALIZE
CD
CD
RECORD
www.freeservicemanuals.info
Digitized in Heiloo Netherlands
To Next Page
Loading...
