Philips FW2017 - Adjustment Table

TUNER Adjustment table
Scope / Voltmeter
[ne | samme | ater [oe
1700 kHz 5105 7,6V + 100 mV
AM (2-band version)
530 - 1700 kHz ")
LW
148 - 284 kHz
MW (8-band version)
522 - 1611 kHz)
mod
=
1
kHz
87,5
MHz
5101
4)
Af
=
22,5
kHz
5102
4
108
Mi
[ern
|
mod
=
1
kHz
108
MHz
4)
2103
Af
=
22,5
kHz
2109
4
STEREO DECODER
98 MHz
carrier
A
98
MHz
19
kHz
+
50
Hz
1 mV
98 MHz
carrier
A
98
MHz
3114
12
UV
98
MHz
99
MHz
carrier A or
15 UV 97 MHz
98 MHz 99 MHz
FM
Autostore
»
carrier
A
or
350
[LV
97
MHz
B
522 kHz
via 100nF
560
kHz?)
560
kHz")
Site
uw
558
kHz
558
kHz
mod
=
1
kHz
30%
AM
1600
kHz")
1600
kHz")
1494 kHz Cc 1494 kHz
530 kHz 1V + 200 mV
VARICAP ALIGNMENT
10V + 50 mv”
87,5 - 108 MHz 1,15V + 250 mv
cae 2,7V + 400 mV
284 kHz 5105 8,4V + 200 mV
1611 kHz 8,5V + 100 mV
fi
SCOMMAMMMMSHVSSMMBDOOCABIBIMMMBVDSOGOOSOBN MOO MMO MBOIOOMMMOOMMAGOMMONOODMOOVOBOBOIOOAVI
PW WPS APD ENG? B.C GD DG GV G1 TT ae UT ae ee ie ee WDD WW 7 WD O10 OT WD O_O? G7: U1 FS. ND GO FD WFD 10 OE GINS OOO UT OD & DODD
108 MHz
Af = 500 kHz
as low as possible
symmetrical and max.
height
adjust so that voltage
switches from low to
high
press DOWN or UP and
check that set stops at
98 MHz
press DOWN or UP and
check that set stops at
98 MHz
522 kHz ©)
Af = 10 kHz
as low as possible
symmetrical and max.
height
Cs 57 085
n
a3
2 3 4 5 6 7
<> AM FRAME AERIAL <<.
OVER 1 1104
FRAME 1107
COVER 2 1108
SCREENING PLATE
ioe)
ANOT FOR SETS WITH LW ## ONLY FOR JAPAN
@FOR SETS WITH LW + NOT FOR JAPAN
He
ONLY
FOR
FTZ
@NOT
FOR
AZS712
/AZI71I0
Sa2NB
BES2esy
@NOT
FOR
FTZ
Sess
sssssss
easia por po =
BASIC SETS ¢ FR320 (eee fe tsie|
FR330
11 1106
FW 2017 FW 2017
FW 2016 - FW 2017
AZ 9710 - AZ 9712 (NO MUTE - NO| AUTOSTORE)
ia)
3104 217 25450 PUNT
¢t Repeat
1)
2)
3)
4)
5)
8)
used in AUSTRALIA, CANADA and USA versions.
used in European versions.
For all sets except FTZ versions adjust coil 5101 for nominal position (top of core approx. 3mm fram topedge coil).
only for FTZ versions (metal screening cabinet)
Connect G136 to GND to switch set into Autostore sensitivity
via low impedance (5Q) direct to pin 10 of 7103 (see fig. 1).