23
English
Viewing the Clock
You can view the clock (if it is set) while
the system is in standby mode or any
source mode. It will be displayed for about
7 seconds.
• Press CLOCK/TIMER briefly
(on the
system only)
.
™ “10:38” (the current time) will be
displayed.
™ “--:--” will be displayed if the
clock is not set.
Setting the Clock
The clock is set in 24-hour mode, e.g.
“00:00“ or “23:59“. Before setting
the clock, you must be in the View Clock
mode.
1 Press CLOCK/TIMER to select clock
mode.
™ “00:00” or the current time starts
flashing.
2 Set the hour with à or á.
3 Set the minute with í or ë.
4 Press CLOCK/TIMER again to store the
setting.
™ The clock starts.
• To exit without storing the setting, press
Ç on the system.
Notes:
– During clock setting, if no button is
pressed within 90 seconds, the system
will exit clock setting mode
automatically.
– When a power interruption occurs, the
clock setting is erased.
– To set the time with RDS clock, see
"Receiving RDS Radio Station" under
TUNER section.
INTERACTIVE SOUND STUDIO
TAPECD
PROG
CLOCK/
TIMER
NEWS!
RDS
DOLBY B
NR
DUB
(HSD)
REC
STANDBY
ON
A.REV
TUNER AUX
PRESET
▲
▲
STOP•CLEARSEARCH • TUNING PLAY • SIDE
MINI HIFI SYSTEM
CD1 • 2 • 3
CDR
BAND
TAPE 1 • 2
M
O
R
E
E
N
T
E
R
J
O
G
NEWS/TA
RDS/
CD TEXT
DOLBY B
NR
M
A
X
S
O
U
N
D
MIC
MIC
LEVEL
V
O
L
U
M
E
SURF
DSC
PERSONAL
DBB
HOLD
STROBE VEC
PAN
SOUND CONTROL
DISPLAY
MAX
VEC
DBB
CLOCK TIMER
Setting the Timer
• The system can switch on to CD,
TUNER, or TAPE 2 mode automatically
at a preset time. It can serve as an
alarm to wake you up.
• Before setting the timer, make sure the
clock is set correctly.
• The timer will always be switched on
once it is set.
• The volume of the timer will start to
increase from the minimum level
until the volume level before the set
is switched to standby mode.
1 Press and hold CLOCK/TIMER for more
than 2 seconds to select timer mode.
™ “00:00” or the last set timer starts
flashing. The TIMER flag flashes.
™ The last selected source is lit while
other available sources are flashing.
2 Press CD, TUNER or TAPE to select the
desired source.
• Before selecting CD or TAPE, make sure
a CD or tape is loaded in the CD tray or
tape deck 2.
3 Press à or á to set the hour for the
timer to start.
4 Press í or ë to set the minute for
the timer to start.
5 Press CLOCK/TIMER to store the start
time.
™ The timer is now set.
™ The TIMER flag remains on the display.
• At the preset time, the timer will be
activated.
™ The selected source will be played.
Notes:
– During timer setting, if no button is
pressed within 90 seconds, the system
will exit timer setting mode
automatically.
– If the source selected is TUNER, the last
tuned frequency will be switched on.
– If the source selected is CD, playback
will begin with the first track of the last
selected disc. If the CD trays are empty,
the TUNER will be selected instead.
– If the source selected is TAPE, and if the
preset time is reached during high
speed dubbing, the TUNER will be
selected instead.
To switch off the TIMER
1 Press CLOCK/TIMER for more than 2
seconds.
2 Press Ç on the system to cancel the
timer.
™ The timer is now switched off.
™ The display will show "OFF" and the
TIMER flag disappears.
To start the TIMER again
(for the same
preset time and source)
1 Press CLOCK/TIMER for more than 2
seconds.
2 Press CLOCK/TIMER again to store the
start time.
™ The timer is now switched on.
™ The TIMER flag appears on the display.
To Next Page
Loading...
