Philips HTS5100B - Program Playback; Random Playback

27
SPECIAL PLAYBACK
EN
You can play back the disc/card in your desired order.
1) In stop mode, press [MODE].
• The program screen will appear.
2) Use [K / L] to select a track / file, then press [OK].
• For MP3, WMA and JPEG files, use [K / L] to select a
folder, then press [OK] first, and then use [K / L] to
select a file, then press [OK].
•Press [CLEAR] to erase the last file of the program.
•Use [K / L] to select “All Clear” at the bottom of the
list to erase all the tracks / files in the program.
• The programmed tracks / files is displayed in the right
hand screen.
•Use [s / B] to go back / forward between the
hierarchy of folders.
3) Press [PLAY B] to start program playback.
• Programmed file list will appear and the program
playback will start.
To exit from the program playback mode:
•Press [BACK U] in stop mode.
This function shuffles the playback order of tracks / files.
1) In stop mode, press [MODE] twice.
• The random screen will appear.
2) Press [PLAY B] to start random playback.
To exit from the random playback mode:
•Press [MODE] in stop mode.
Program Playback
1. audio CD
MP3/WMA/JPEG
:
:
Track information
File information
2. Playback Status
3. Cumulative playback time of all tracks / files in the
programmed list.
4. Programmed list : Track / File list in the
programmed order.
5. Track / File list : Track / File list in the original
order.
6. audio CD
MP3/WMA/JPEG
:
:
“CD-DA” will be displayed.
Current Disc, SD Memory Card,
or folder name will be displayed.
Track001 Track 001
Track002
Track 002
Track003
Track004
Track005
Track006
Track007
Program
CD-DA Total 0:05:43
Page Down
- - / 19
42
1
6
5
2
3
4
e.g.) audio CD
Track001
Track002
Track003
Track004
Track005
Track006
Track007
Program
CD-DA Total 1:05:43
Page Down
1 / 16 0:01:05
42
e.g.) audio CD
Note
• During program playback, press [STOP C] once to
set the resume point, and then press [PLAY B] to
resume program playback from where [STOP C] was
pressed (audio CD) or from beginning of the file
where [STOP C] was pressed (MP3/WMA/JPEG).
• During program playback, press [STOP C] twice to
display the program screen. To go back to the
normal program playback, press [BACK U] to exit
from the program screen, then press [PLAY B].
• Up to 99 tracks / files can be entered.
• To repeat the current track / file in the program,
press [REPEAT] repeatedly until “ Track”
appears during playback. To repeat the entire
program, press [REPEAT] repeatedly until “ All”
appears during playback.
• Playback from a desired track / file and random
playback are not available during program playback.
•Press [MODE] to switch to the random playback
mode.
• The program will be cleared when;
- the unit is turned into the standby mode.
- the media mode is switched to the other mode.
- the disc / card is removed. (as for “Disc” mode, just
opening the disc tray will clear the program info.)
Random Playback
1. audio CD
MP3/WMA/JPEG
:
:
Track information
File information
2. Playback status
3. Total playback time of all tracks / files.
4. Track / File list : Track / File list in the original
order will be displayed.
5. audio CD
MP3/WMA/JPEG
:
:
“CD-DA” will be displayed.
Current Disc, SD Memory Card,
or folder name will be displayed.
Track1.mp3
Track2.mp3
Track3.mp3
Track4.mp3
Track5.mp3
Track6.mp3
Track7.mp3
Random
CD-DA Total 1:01:23
Page Down
- - / 16
42
1 2
3
5
4
e.g.) audio CD
Introduction Connections Basic Setup Playback Radio Tuning
OthersFunction Setup