electr1dan. Never use wtth an extension
cord
unless
plug
can be f
ully
inserted.
Do
not
a
lter
the
pl
u
g.
TO
PREVE
NT
ELECTRIC
SHOCK,
MATCHWIDE BLADE OF PLUGTOWIDE SLOT
WARNINGS
AND
CAUTIONS
for
Philips
Hue
indoor Lightstrips Risk
of
electric
shock - Do
not
use device where directly exposed
to
water. The device
is
for
in
d
oor
use only. Dry location use only.
WARNINGS
AND
CAUTIONS
for
Phtlfps
Hue
outdoor Ltahtstnps
WARNING: When using
outdoor
use
portable
lumlnalres, basic safety
preca
utions
should always
be
followed
to
reduce
the
risk
of
fire, electric shock,
and
personal injury, including
the
following:
a) Use
only
three-wire
outdoor
extension cords
that
have
three-prong
grounding plugs and grounding receptacles
that
accept
the
ap
pliance's plug.
b) Ground Fault Circuit Interrupter
(GFCI)
protection
is
to
beprovided
on
the
drcuit(s)
or
outlet(s)
to
be
used
for
the
wet
location
portable
lumlnalre
Receptacles are available having built-inGFCI protection and are
able
to
be
used
for
this measure
of
safety.
c) Use
only
with
an extension cord
for
outdoor
use. such as an extension
cord
of
cord
type
SEW,
SEOW,
SEOOW.
SOW. SCOW,
STW.
STOW, STOOW,
SJEW,
SJEOW,
SJEOOW,
SJW,
SJOW, SJOOW,
SJTW,
SJTOW.
or
SJTOOW.
SAVE
THESE
INSTRUCTIONS.
WIRELESS SPECIFICATIONS
for
all
Philtps
Hue
products
Wireless
RF
mode
frequency band: 2,400-2,483.5 MHz
Operating channels Zigbee
if
applicable: channels
11
-
26
Operating channels Bluetooth
if
applicable : channels
0-39
Maximum
transmitted
power
<20
dBm
Enviro
nmental
spedflcatton Phtltps
Hue
indoor Ltghtstrtps Temperature
(Storage):
-25
°C
to
60
°C /
-13
°F
to
140 °F Temperature (operation): 0°C
to
35
°C
/ 32°F
to
86°F
Relative humidity: 5 - 95%
non
condensing
Environ
mental
spedflcatfon Phtlips Hue outdoor Ltghtstrtps Temperature
(Storage): -25
°c
to
60
°C /
-13
°F
to
140 °F Temperature (operation):
-20
°C
to
40
°C
/
-4
°F
to
104 °F Relative humidity: 5 - 95%
non
condensing
IMPORTANT
SAFETY INSTRUCTIONS The manufacturer
advises
the
correct use
of
luminaires lighting fixtures! Therefore
alw
a
ys
follow
these instructions
to
ensure correct and safe installation and functioning
of
the
lumlnalre and keep
it
for
future reference. Turn off electrical
power
at
main fuse
or
circuit breaker
box
before
commencing installation. maintenance
or
repair.
If
1n
doubt,
consult
a
qualified
electrician
or
contact
your
retail
outlet
Ensure
that
you always
install
the
lumlnatre
to
the
local electrical code. Certain regulations
indicate
that
lumfnalres should
be
installed
by
a qualified electrician. Always
use wire nuts/connectors rated
for
the
correct gauge
and
number
of
wires
used. CAUTION: Be certain
that
no
bare wire strands are exposed outside
of
the
wire
nuts/connections
(If applicable). Be careful
not
to
damage or
cut
the
wire Insulation (covering) during installation. Do
not
permit
wires
to
contact
any
sharp edges. Do
not
remove thermal insulation pad(s). Doing so
will
result
in
increased temperatures
and
possible risk
of
fire. Maintain
interior
lighting
with
a
dry
cloth
duster,
do
not
use abrasives
or
solvents. Avoid Liquid
on
all
electrical
parts. Always consider
all
the
technical specifications
of
the
luminaire. Verify
the
stated
icons
on
the
identification
label
on
the luminaire and
the
icons
that
are shown
in
part
A
of
your
safety instructions.
CLEANING
AND
MAINTENANCE: Do
not
clean
the
device when
it
is
on
and
connected
to
the
power
supply.
To
avoid scratching,
the
product
should
only
be
cleaned
with
a
soft
dry
cloth. Do
not
use cleaning agents
to
clean
the
device. Manage
in
accordance
with
disposal laws
in
your
area.
To Next Page
Loading...
