Philips Norelco 3000 Series - 5. If you have more questions regarding the cleaning instructions of your Philips Shaver, refer to your user manual or call us for support.

Philips Norelco 3000 Series

8 pages

To Previous Page

To Previous Page

Loading...

5. If you have more questions regarding the cleaning instructions of your Philips Shaver, refer to your

user manual or call us for support.

Table of Contents

Philips Norelco Shaver 3100 Dry electric shaver, Series 3000 S3310/811
Frequently Asked Questions1
1. Blocked shaving heads: If you see the exclamation mark along with a tap and a shaving head symbol, this means the motor of your shaver cannot run anymore because the shaving heads are soiled or damaged. When this happens, you have to clean the shav...2
2. Overheating: Your shaver may overheat due to excessive charging. When this happens, the shaver automatically switches off. Let it cool down for a few minutes and try turning it on again.2
3. Metallic object on charging pad: If you see an exclamation mark flashing on your Qi pad, it means that there is a metal object placed on it. This will cause the Qi pad to automatically turn off. Remove the object and restart the charging pad after ...2
1. Dry shaving can be done almost anywhere, even on the go, and there is hardly any cleaning involved.4
2. Wet shaving feels refreshing and is often beneficial for sensitive skin as it reduces friction and irritation caused by a blade.4
1. Always wash your face with water and soap before you start shaving.5
2. Apply your favorite shaving gel or foam to your skin.5
3. Start shaving by moving your shaver in circular movements over your skin. This ensures that all hair growing in different directions are removed from your skin.5
1. Firstly, always wash your face with some water and soap and then dry it properly.5
2. Allow at least 15 minutes for your skin to dry completely before you start shaving.5
3. Move the shaver on your skin in circular movements to cut all hair growing in different directions.5
1. Pull the shaving head holder off the body of the shaving unit.5
2. Twist the retaining rings inside your shaving head holder and pull them out one by one.6
3. Remove the shaving heads from the shaving head holder.6
4. Each shaving head consists of a cutter and a guard. Please keep in mind that the cutter and guard are not interchangeable. So make sure you keep them together.6
5. Put the shaving heads back into the shaving head holder.6
6. Reattach the shaving head holder to the bottom part of the shaving unit.6
1. Turn on your shaver and rinse it under a warm water tap.6
2. Turn off the shaver and remove the top part of your shaving head.6
3. Rinse the top part of your shaving head under warm running water for at least 30 seconds. Attach it back on the shaving head once it is completely dry.6
4. Carefully shake off excess water from your shaver and let it air dry. Never dry the shaver head with a towel or tissue, as this may damage it.6
1. Turn on your Philips Shaver and rinse it with warm water for at least 30 seconds.6
2. Press the release button to open the shaving head.6
3. Rinse the shaving head holder under warm running water.6
4. Carefully shake off excess water and keep the shaving head holder open until it is completely dry. Once dried you can close the shaving head holder, making sure you hear a click.6
1. Pull off the shaving head from your Philips Shaver.7
2. Rinse the shaving head under a warm water tap for at least 30 seconds.7
3. Shake off the excess water from the shaving head and let it air dry.7
4. Press the release button to open the top part of the shaving head and pull it off the shaving head. Rinse it with water and click it back on the shaving head once it is clean and dry.7
5. Once the shaving head is completely dry, reattach it to your Philips Shaver.7
1. Rinse the shaver under a warm water tap and shake off excess water from it.7
2. Press the top part of your Philips SmartClean system to open the area where you can place your shaver. Hold your shaver upside down pointing towards the SmartClean system and place it in the SmartClean holder.7
3. Tilt the shaver backward and press down the top cap of the SmartClean system until you hear a click sound, confirming that the shaver is locked in.7
4. Press the on/off button on the SmartClean system to start the cleaning program. You will see a cleaning symbol blinking on the SmartClean system confirming that the cleaning program is working.7
5. If you have more questions regarding the cleaning instructions of your Philips Shaver, refer to your user manual or call us for support.8

Other manuals for Philips Norelco 3000 Series

Related product manuals

Preview: Norelco Beardtrimmer 3000

Norelco Beardtrimmer 3000

Preview: Philips Norelco 3500

Philips Norelco 3500

Philips Norelco 3601X

Preview: Philips Norelco 3605x

Philips Norelco 3605x

Philips Norelco 3405LC

Philips Norelco 3801XL

Preview: Philips Norelco NT 3600

Philips Norelco NT 3600

Preview: Philips Norelco

Philips Norelco

Preview: Philips Norelco 7700

Philips Norelco 7700

Preview: Philips Norelco 9300

Philips Norelco 9300

Preview: Philips NORELCO AT810

Philips NORELCO AT810

Preview: Philips NORELCO S7371

Philips NORELCO S7371