© 2007 Philips Lighting Company. All rights reserved.
Printed in USA 08/07
P-5813-B
www. philips.com
Philips Lighting Company
200 Franklin Square Drive
P.O. Box 6800
Somerset, NJ 08875-6800
1-800-555-0050
A Division of Philips Electronics North America Corporation
Philips Lighting
281 Hillmount Road
Markham, Ontario
Canada L6C 2S3
1-800-555-0050
A Division of Philips Electronics Ltd.
Printed on chlorine free paper from Sappi Fine Paper mills, who are accredited with EMAS environmental certification.
Sappi claims that the pulp used in the manufacture of Magno Dull paper is derived from environmentally certified forests.
P
hilips TuffGuard
™
H
igh Intensity Discharge
Coated Lamps—HPS Lamps
Ordering, Electrical and Technical Data
Max.
R
ated Approx.
Product Nom. Pkg. Avg. Life Initial
Number Description Watts Volts Qty. Bulb Base (Hrs)
1
Lumens
2
Availability
20218-4 C70S62 12PK TG 70 52 12 ED-23
1
⁄2 Mogul 24,000 6500 Made to Order
2
0219-2 C100S54 12PK TG 100 55 12 ED-23
1
⁄2 M
ogul 24,000 9400 Made to Order
2
0220-0 C150S55 12PK TG 150 55 12 ED-23
1
⁄2 M
ogul 24,000 15,800 Made to Order
2
0222-6 C250S50 12PK TG 250 100 12 ED-18 Mogul 24,000 27,000 Stocked
20458-6 C50S68/M 12PK TG 50 52 12 BF-55 Medium 24,000 4000 Made to Order
20460-2 C100S54/M 12PK TG 100 55 12 BF-55 Medium 24,000 9500 Made to Order
1
) Average life under engineering data with lamps turned off and restarted once every 12 operating hours.
2) Protective coating may reduce actual lumens by up to 5%.
Above specifications are subject to change without notice.
WARNINGS:
• Coating can withstand bulb wall temperatures up to 500°F, subject to the following conditions:
1) Lamp must be installed and operated in ambient temperature below 150°F.
2) Lamp is not used in fixture that does not allow heat dissipation.
RECOMMENDED WARNINGS, CAUTIONS,AND OPERATING INSTRUCTIONS
For High Pressure Sodium Lamps
R
“WARNING:
These lamps must be operated in fixtures designed for use with High Pressure Sodium
lamps.The fixture wattage rating must match the wattage indicated on the outer glass bulb. Do not scratch
the outer bulb or subject it to pressure as this could cause the outer bulb to crack or shatter.A partial vacuum
in the outer bulb may cause glass to fly if the glass is struck.Operating the lamp improperly may result in
PERSONAL INJURY, PROPERTY DAMAGE, BURNS AND FIRE.
1. If the outer glass bulb is broken, shut off power immediately and remove the lamp after it has cooled.
2. Use only auxiliary equipment meeting Philips and/or ANSI standards. Use within voltage limits recommended
by ballast manufacturer.
A.Operate lamp only within specified limits of operation.
B. For total supply load refer to ballast manufacturers electrical data.
3. Protect lamp base, socket and wiring against moisture, corrosive atmospheres and excessive heat.
4. Replace the lamp if the outer glass bulb has been scratched, cracked or damaged in any way.
5. If a lamp bulb support is used, be sure to insulate the support electrically so as to avoid possible decomposition
of the bulb glass.
6. Do not use this lamp in a fixture which redirects a substantial portion of the energy toward the arc tube and
its immediate vicinity, as this may lead to very early lamp failure.
7. Take care in handling and disposing of lamps. If arc tube is broken, avoid skin contact with any of the contents
or fragments.
8. The arc tube of this lamp contains sodium and mercury. Dispose of in accordance with federal, state and local
requirements.
Made to order requires 3 week lead time
(No product returns on made to order lamps)
To Previous Page
Loading...
Need help?
General
