S P E C I F I C A T I O N S
3
MONOBLOCK SPECIFICATIONS
F
requency Response: . . . . . . . . . . . . . .± 1dB from 20Hz to 300Hz
Signal to Noise Ratio: . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>90dB
Subsonic and Low Pass Crossovers: . . Linkwitz-Riley 24dB per octave
Low Pass Crossover Range: . . . . . . . . . . . . . . . . . .30Hz to 300Hz
Subsonic Crossover Range: . . . . . . . . . . . . . . . . . . . . . 5Hz to 55Hz
Bass
Boost: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +18 dB @ 45 Hz
Input Sensitivity: . . . . . . . . . . . . . . . . . . . .200 millivolts to 8 volts
Lowest Recommend Load: . . . . . . . . . . . . . . . . . . . . . . . . . .1 ohm
X400.1
Into 4, 2 and 1 ohm . . . . . . . . . .400 x 1
Recommended Fuse Size: . . . . . . . .40A
Power/Ground Wire Size . . . . . .8 Gauge
Dimensions:
. . . . .14L x 10.6W x 2.5H
X600.1
Into 4, 2 and 1 ohm . . . . . . . . . .600 x 1
Recommended Fuse Size: . . . . . . . .60A
P
ower/Ground Wire Size . . . . . .4 Gauge
Dimensions:
. . .18.25L x 10.6W x 2.5H
X1200.1
Into 4, 2 and 1 ohm . . . . . . . . .1200 x 1
Recommended Fuse Size: . . . . . . .100A
Power/Ground Wire Size . . . . . .4 Gauge
Dimensions: . . . . .22L x 10.6W x 2.5H
TWO & FOUR CHANNEL SPECIFICATIONS
Frequency Response: . . . . . . . . . . . . . .± 1dB from 20Hz to 20kHz
Signal to Noise Ratio: . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>100dB
High and Low Pass Crossovers: . . .Linkwitz-Riley 24dB per octave
Crossover Range: . . . . . . . . . . . . . . . . . . . . . . . . . . .40Hz to 400Hz
Bass Boost: . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+18 dB @ 45 Hz
Input Sensitivity: . . . . . . . . . . . . . . . . . . . . .200 millivolts to 8 volts
Lowest Recommend Load: . . . . . . .2 ohm bridged or 1 ohm stereo
X100.2
Into 4, 2, and 1 ohm stereo . . . .100 x 2
Into 8, 4, and 2 ohm bridged . . .200 x 1
Recommended Fuse Size: . . . . . . . .40A
Power/Ground Wire Size . . . . . .8 Gauge
Dimensions: . . . . .14L x 10.6W x 2.5H
X200.2
Into 4, 2, and 1 ohm stereo . . . .200 x 2
Into 8, 4, and 2 ohm bridged . . .400 x 1
Recommended Fuse Size: . . . . . . . .60A
Power/Ground Wire Size . . . . . .4 Gauge
Dimensions: . . . .15.5L x 10.6W x 2.5H
X100.4
Into 4, 2 and 1 ohm stereo . . . .100 x 4
Into 8, 4 and 2 ohm bridged . . .200 x 2
Recommended Fuse Size: . . . . . . . .80A
Power/Ground Wire Size . . . . . .4 Gauge
Dimensions: . . .18.25L x 10.6W x 2.5H
X200.4
Into 4, 2 and 1 ohm stereo . . . .200 x 4
Into 8, 4 and 2 ohm bridged . . .400 x 2
Recommended Fuse Size: . . . . . . .120A
Power/Ground Wire Size . . . . . .4 Gauge
Dimensions: 22L x 10.6W x 2.5H
Continuous Output Power: (Wattage Rated according to CEA 2006 Specifications of 14.4VDC and no more than 1%THD)
Xe.flow
™
–Efficient Cooling!
Combines traditional internal heat sink design with cold air induction via a temperature controlled variable speed fan.
This provides forced cold air movement across the Xenon amplifier heatsink. In addition, a proprietary thermal feedback
circuit continuously monitors the temperature of the amplifier and optimizes the amplifier’s operation to guarantee
the amplifier will continue to play regardless of how hard the amplifier is driven.
Xe.load
™
–Max Power for All Loads!
Plug-n-Play speaker sensing optimizes amplifier to deliver full power into any load between (4ohm -1ohm). Xe.load
™
makes life easy by allowing the user to get full power regardless of the impedance of his woofer or full range speakers.
Xe.tune
™
–Crossover Features!
Audiophile 24dB Linkwitz-Riley crossover controls provide state of the art slope control. The Xe.tune
™
detented control
system allows users to perfectly adjust crossover slope every time without errors or guess work. Every Xenon amplifier has
a separately defeatable continuously variable high and low pass filter for maximum processing flexibility
Now that’s total control!
To Next Page
Loading...
General