Page 12 ;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1 Item 64254
EF;6GH IJ6KFGLIM NFLMG6MFMO6E6GPJ
I/*(,$"83%L8#$('4$"&8#
%K*,9%$.*%6MGLK6%LNJIKGFMG%EF;6GH%LM;IKNFGLIM%#*4$"&8%,$%$.*%+*3"88"83%&2%$."#%
5,8',7%"847'9"83%,77%$*\$%'89*(%#'+.*,9"83#%$.*(*"8%+*2&(*%#*$%'/%&(%'#*%&2%$."#%/(&9'4$1
L8#/*4$%G&&7%+*2&(*%'#*=%7&&Y"83%2&(%9,5,3*9=%7&&#*=%,89%5"##"83%/,($#1%%
L2%,8[%/(&+7*5#%,(*%2&'89=%9&%8&$%'#*%G&&7%'8$"7%(*/,"(*91
Q&(Y/"*4*%,89%Q&(Y%F(*,%E*$%P/
1. Designate a work area that is clean and well-lit.
The work area must not allow access by children
or pets to prevent distraction and injury.
2. Route the air hose along a safe route to reach
the work area without creating a tripping hazard
or exposing the air hose to possible damage.
The air hose must be long enough to reach
the work area with enough extra length to
allow free movement while working.
3. Secure loose workpieces using a vise or clamps
(not included) to prevent movement while working.
4. There must not be hazardous objects
(such as utility lines or foreign objects) nearby
that will present a hazard while working.
O&8$,4$%F4$',$"&8%N*4.,8"#5%U*2"8"$"&8
The contact actuation mechanism allows rapid placement of fasteners. The Tool should only actuate if the
Workpiece Contact is pressed against the workpiece and the Trigger is pulled. It should actuate again if the Trigger
is released and pulled OR if the Workpiece Contact is lifted and pressed against the workpiece again. The Tool
should not actuate if the Workpiece Contact is not pressed against an object. O&8$,4$%F4$',$"&8%#.&'79%&87[%+*%
*8,+7*9%,89%'#*9%+[%#Y"77*9%&/*(,$&(#%).&%,(*%,),(*%&2%$.*%.,`,(9#%,89%'#*%/(&/*(=%#,2*%)&(Y%/(,4$"4*#1
O&8$,4$%F4$',$"&8%N*4.,8"#5%G*#$"83%J(&4*9'(*
GI%JK6!6MG%E6KLIPE%LMXPKH%;KIN%FOOLU6MGFT%ULEOWFKR6-%
65/$[%$.*%$&&7%+*2&(*%$."#%/(&4*9'(*1%%J&"8$%$.*%$&&7%,$%,%/"*4*%&2%#4(,/%)&&9%).*8%$*#$"831
1. Disconnect the Tool from the air supply.
2. Empty the magazine of fasteners.
3. Check that the Trigger and the Workpiece
Contact move freely, without sticking.
4. Connect the air supply to the Tool and
set within the Operating Air Pressure
indicated on the Specification chart.
5. Test the Tool by pressing the Workpiece Contact
against the workpiece without pulling the Trigger.
G.*%G&&7%5'#$%8&$%4[47*%e,4$',$*f1
If it cycles (actuates), stop immediately and have
it repaired by a qualified service technician.
6. Hold the Tool away, or off of the workpiece.
The Workpiece Contact should return to its original
position. Squeeze the Trigger.
G.*%G&&7%5'#$%8&$%4[47*%e,4$',$*f1
If it cycles (actuates), stop immediately and take
the Tool to a qualified service technician.
7. Press the Workpiece Contact against the workpiece
and squeeze the Trigger.
G.*%G&&7%5'#$%4[47*%e,4$',$*f%&87[%&84*1
Release the Trigger, slide the Tool to a fresh piece of
wood, and squeeze it again.
G.*%G&&7%5'#$%4[47*%e,4$',$*f%,3,"8%&87[%&84*1
With the Trigger depressed, carefully lift the Tool
and press it against the workpiece again in a new
location.
G.*%G&&7%5'#$%4[47*%e,4$',$*f%,3,"8%&87[%&84*1
If it fails to act in the manner explained in bold,
have it repaired by a qualified service technician.
F4$',$"&8%N&9*
E"837*%E*<'*8$",7%G("33*(%I/$"&8-
For precise driving of fasteners, a single-sequential actuation valve is available. Contact Harbor Freight
Customer Service at 1-888-866-5797 to order the Replacement Sequential Trip Mechanism, 15689.
To Next Page
Loading...